Toothbrush Head Stand/ro: Difference between revisions

From FreeCAD Documentation
No edit summary
(Updating to match new version of source page)
 
(17 intermediate revisions by the same user not shown)
Line 1: Line 1:
<languages/>
<languages/>

<div class="mw-translate-fuzzy">
{{TutorialInfo/ro|Topic=Modeling|Level=Beginner|Author=[[User:EmmanuelG|EmmanuelG]]|Time=1 hour|FCVersion=0.16 or greater|Files=[https://www.thingiverse.com/thing:2403310 Thingiverse 2403310]}}
{{TutorialInfo/ro|Topic=Modeling|Level=Beginner|Author=[[User:EmmanuelG|EmmanuelG]]|Time=1 hour|FCVersion=0.16 or greater|Files=[https://www.thingiverse.com/thing:2403310 Thingiverse 2403310]}}
</div>


== A daily-life problem ==
== A daily-life problem ==
Line 6: Line 9:
Periuțele electrice de dinți mai rar vin cu un suport pentru cap, în timp ce într-o familie, veți vedea adesea mai multe capete folosite cu un singur corp. Mulți oameni se confruntă cu o problemă comună, ceea ce duce la o varietate de soluții, după cum puteți vedea pe Thingiverse (200 la 800 de proiecte sunt legate de acest lucru). Iată primul răspuns și cum să îl proiectăm.
Periuțele electrice de dinți mai rar vin cu un suport pentru cap, în timp ce într-o familie, veți vedea adesea mai multe capete folosite cu un singur corp. Mulți oameni se confruntă cu o problemă comună, ceea ce duce la o varietate de soluții, după cum puteți vedea pe Thingiverse (200 la 800 de proiecte sunt legate de acest lucru). Iată primul răspuns și cum să îl proiectăm.


<div class="mw-translate-fuzzy">
This tutorial will take you through the steps needed to model the part shown in the image below using basic tools from the [[PartDesign Workbench|Part Design Workbench]] (many of the tools and capabilities are not covered).
This tutorial will take you through the steps needed to model the part shown in the image below using basic tools from the [[PartDesign Workbench|Part Design Workbench]] (many of the tools and capabilities are not covered).
</div>


[[Image:TBHS-model.png|center]]
[[Image:TBHS-model.png|center]]


== First idea : a plate ==

<div class="mw-translate-fuzzy">
== First idea : a plate ==
== First idea : a plate ==
*From the start-page, select [[Image:Workbench_PartDesign.png‎‎]] ''Part Design'', or create a new document and select the ''Part Design'' workbench.
*From the start-page, select [[Image:Workbench_PartDesign.png‎‎]] ''Part Design'', or create a new document and select the ''Part Design'' workbench.
[[Image:TBHS-0.png|center]]
[[Image:TBHS-0.png|center]]
</div>


[[Image:TBHS-0.png|center]]
=== Create a sketch ===
*Click on [[Image:Sketcher_NewSketch.png|32px]] [[Sketcher_NewSketch|'''New sketch''']]. Either from the contextual task menu at the left, or the toolbar above or from the Part Design menu at the top.
[[File:TBHS-1.JPG|800px|center]]


=== Create a sketch ===

*Click on [[Image:Sketcher_NewSketch.svg|32px]] [[Sketcher_NewSketch|'''New sketch''']]. Either from the contextual task menu at the left, or the toolbar above or from the Part Design menu at the top.

[[File:TBHS-1.JPG|800px|center]]


A dialog prompts you to choose the sketch orientation and provide an offset.
A dialog prompts you to choose the sketch orientation and provide an offset.
Line 24: Line 36:


[[File:TBHS-2.JPG|800px|center]]
[[File:TBHS-2.JPG|800px|center]]



You now are facing the XY plane from above, and have access to the drawing tools.
You now are facing the XY plane from above, and have access to the drawing tools.


* Click on [[File:Sketcher_CreateRectangle.png|32px]] [[Sketcher_Rectangle|'''Rectangle''']].
* Click on [[File:Sketcher_CreateRectangle.svg|32px]] [[Sketcher_CreateRectangle|'''Rectangle''']].
* Click to place a first point.
* Click to place a first point.
* Click to place the opposite corner.
* Click to place the opposite corner.
Line 34: Line 45:


[[File:TBHS-3.JPG|800px|center]]
[[File:TBHS-3.JPG|800px|center]]



You now have a floating rectangle of unspecified dimensions.
You now have a floating rectangle of unspecified dimensions.


* Click on a line of the rectangle, you now have access to the constraint tools at the right of the toolbar (depending of the size of your screen you may need to drag them to the left in order to see them all)
* Click on a line of the rectangle, you now have access to the constraint tools at the right of the toolbar (depending of the size of your screen you may need to drag them to the left in order to see them all)
* Click on [[File:Constraint_Length.png|32px]] [[Constraint_Length|'''Length''']]
* Click on [[File:Constraint_Length.png|32px]] [[Sketcher_ConstrainDistance|'''Distance''']]
* A dialog prompts you to set a dimension. Enter 80mm, click OK.
* A dialog prompts you to set a dimension. Enter 80mm, click OK.
* Repeat with the other side of the rectangle, also 80mm.
* Repeat with the other side of the rectangle, also 80mm.


[[File:TBHS-4.JPG|800px|center]]
[[File:TBHS-4.JPG|800px|center]]



You now have a floating square.
You now have a floating square.
Line 50: Line 59:
* Click on the lower left point of the square.
* Click on the lower left point of the square.
* Click on the origin of the XY plane (at the intersection of the two thick lines).
* Click on the origin of the XY plane (at the intersection of the two thick lines).
* Click on [[File:Constraint_PointOnPoint.png|32px]] [[Sketcher ConstrainCoincident ‎|'''Coincident''']].
* Click on [[File:Constraint_PointOnPoint.svg|32px]] [[Sketcher ConstrainCoincident ‎|'''Coincident''']].


[[File:TBHS-5.JPG|800px|center]]
[[File:TBHS-5.JPG|800px|center]]


You now have a totally constrained sketch, as you are told by the solver on the left and the change of color. It is a good practice to always have a totally constrained sketch.

You now have a totally constrained sketch, as you are told by the solver on the left and the change of color.
It is a good practice to always have a totally constrained sketch.


An under-constrained sketch can leave room for unwanted change, if you modify something later on.
An under-constrained sketch can leave room for unwanted change, if you modify something later on.

On the opposite, an over-constrained sketch is also not good. In that case the solver warn you of redundant constraints and you should remove some of them.
On the opposite, an over-constrained sketch is also not good. In that case the solver warn you of redundant constraints and you should remove some of them.


Line 64: Line 72:


[[File:TBHS-6.JPG|800px|center]]
[[File:TBHS-6.JPG|800px|center]]



You now only see the square, and the contextual task menu on the left show you more options than before.
You now only see the square, and the contextual task menu on the left show you more options than before.


=== Create a pad ===
=== Create a pad ===

* Click on [[Image:View-axometric.png|32px]] '''Axonometric''' among the standard views, to better see what will happen.
* Click on [[File:PartDesign_Pad.png|32px]] '''Pad'''.
* Click on [[Image:View-axometric.svg|32px]] '''Axonometric''' among the standard views, to better see what will happen.
* Click on [[File:PartDesign_Pad.svg|32px]] '''Pad'''.
* Enter 4mm and click OK.
* Enter 4mm and click OK.


[[File:TBHS-7.JPG|800px|center]]
[[File:TBHS-7.JPG|800px|center]]


Your sketch is now in volume!


=== Create a sketch on it ===
Your sketch is now in volume !


=== Create a sketch on it ===
* Select the upper face
* Select the upper face


[[File:TBHS-8.JPG|800px|center]]
[[File:TBHS-8.JPG|800px|center]]



The color of the face change and you have more options in the contextual task menu.
The color of the face change and you have more options in the contextual task menu.


* Click on [[Image:Sketcher_NewSketch.png|32px]] '''New sketch'''. As a face was selected it will not ask you to choose a plane.
* Click on [[Image:Sketcher_NewSketch.svg|32px]] '''New sketch'''. As a face was selected it will not ask you to choose a plane.


[[File:TBHS-9.JPG|800px|center]]
[[File:TBHS-9.JPG|800px|center]]


* Click on [[File:Sketcher_Circle.svg|32px]] [[Sketcher_CreateCircle|'''Circle''']], click to place the center, move the pointer and click to define the radius.

* Click on [[File:Sketcher_Circle.png|32px]] [[Sketcher_Circle|'''Circle''']], click to place the center, move the pointer and click to define the radius.
* Draw 4 circles on the pad (of any size)
* Draw 4 circles on the pad (of any size)
* Press {{KEY|ESC}} or click the right mouse button to stop using the tool.
* Press {{KEY|ESC}} or click the right mouse button to stop using the tool.


[[File:TBHS-10.JPG|800px|center]]
[[File:TBHS-10.JPG|800px|center]]



* Select the circles
* Select the circles
* Click on [[File:Constraint_EqualLength.png|32px]] [[Constraint_EqualLength|'''Equal Length''']]
* Click on [[File:Constraint_EqualLength.png|32px]] [[Sketcher_ConstrainEqual|'''Equal Length''']]


[[File:TBHS-11.JPG|800px|center]]
[[File:TBHS-11.JPG|800px|center]]



Now the circles share the same radius.
Now the circles share the same radius.


* Click on [[File:Sketcher_External.png|32px]] [[Sketcher_External|'''External geometry''']].
* Click on [[File:Sketcher_External.svg|32px]] [[Sketcher_External|'''External geometry''']].
* Click on the four sides of the square, it add lines, color magenta.
* Click on the four sides of the square, it add lines, color magenta.


[[File:TBHS-12.JPG|800px|center]]
[[File:TBHS-12.JPG|800px|center]]



Theses lines will serve as reference to position the circles.
Theses lines will serve as reference to position the circles.


* Use [[File:Constraint_Length.png|32px]] [[Constraint_Length|'''Length''']] to position them at 20mm from the edges.
* Click on [[File:Constraint_Length.png|32px]] [[Sketcher_ConstrainDistance|'''Distance''']].
* Click on a center of a circle.
* Click on a magenta line.
* Set distance (20mm from each side).


[[File:TBHS-13.JPG|800px|center]]
[[File:TBHS-13.JPG|800px|center]]



* Click on a circle
* Click on a circle
* Click on [[File:Constraint_Radius.png|32px]] [[Constraint_Radius|'''Radius''']] and set it at 1,5mm.
* Click on [[File:Sketcher_ConstrainRadius.svg|32px]] [[Sketcher_ConstrainRadius|'''Radius''']] and set it at 1,5mm.


[[File:TBHS-14.JPG|800px|center]]
[[File:TBHS-14.JPG|800px|center]]



* To leave the sketch, click either on the "Close" button on the left, or the [[File:Sketcher_LeaveSketch.png|32px]] icon in the toolbar, or press {{KEY|ESC}}.
* To leave the sketch, click either on the "Close" button on the left, or the [[File:Sketcher_LeaveSketch.png|32px]] icon in the toolbar, or press {{KEY|ESC}}.
Line 129: Line 133:
[[File:TBHS-15.JPG|800px|center]]
[[File:TBHS-15.JPG|800px|center]]


=== Create a pad===
=== Create a pad===

* Click on [[Image:View-axometric.png|32px]] '''Axonometric''' among the standard views, to better see what will happen.
* Click on [[File:PartDesign_Pad.png|32px]] '''Pad'''.
* Click on [[Image:View-axometric.svg|32px]] '''Axonometric''' among the standard views, to better see what will happen.
* Click on [[File:PartDesign_Pad.svg|32px]] '''Pad'''.
* Enter 25mm and click OK.
* Enter 25mm and click OK.


[[File:TBHS-16.JPG|800px|center]]
[[File:TBHS-16.JPG|800px|center]]



You have the basic shape, it just need final touches.
You have the basic shape, it just need final touches.


=== Rounding the corners ===
=== Rounding the corners ===

* Holding {{KEY|CTRL}} click on the vertical edge at each corner to select the four of them.
* Holding {{KEY|CTRL}} click on the vertical edge at each corner to select the four of them.


Line 146: Line 151:
[[File:TBHS-17.JPG|800px|center]]
[[File:TBHS-17.JPG|800px|center]]


* Click on [[File:PartDesign_Fillet.svg|32px]] [[PartDesign_Fillet|'''Fillet''']].

* Click on [[File:PartDesign_Fillet.png|32px]] [[PartDesign_Fillet|'''Fillet''']].
* Set the radius at 20mm.
* Set the radius at 20mm.


[[File:TBHS-18.JPG|800px|center]]
[[File:TBHS-18.JPG|800px|center]]



Much better.
Much better.


=== Making it more robust ===
=== Making it more robust ===

We need to add material at the base of the cylinders to make them less prone to snap. Because of the printing orientation these small surfaces will be fragile at the junction with the base.
We need to add material at the base of the cylinders to make them less prone to snap. Because of the printing orientation these small surfaces will be fragile at the junction with the base.


* Select the circles at the base of the cylinders
* Select the circles at the base of the cylinders
Line 162: Line 166:
[[File:TBHS-19.JPG|800px|center]]
[[File:TBHS-19.JPG|800px|center]]


* Click on [[File:PartDesign_Chamfer.svg|32px]] [[PartDesign_Chamfer|'''Chamfer''']].

* Click on [[File:PartDesign_Chamfer.png|32px]] [[PartDesign_Chamfer|'''Chamfer''']].
* Set it to 2mm.
* Set it to 2mm.


[[File:TBHS-20.JPG|800px|center]]
[[File:TBHS-20.JPG|800px|center]]


=== Chamfer the edges ===
=== Chamfer the edges ===

* Select the face under the base, add a [[File:PartDesign_Chamfer.png|32px]] '''Chamfer''' of 0,5mm.
* Select the face under the base, add a [[File:PartDesign_Chamfer.svg|32px]] '''Chamfer''' of 0,5mm.


The first layer of plastic is often being squashed a little too much, this will compensate that and save you time in cleaning the model. If the first layer is ok that will make it only nicer
The first layer of plastic is often being squashed a little too much, this will compensate that and save you time in cleaning the model. If the first layer is ok that will make it only nicer


[[File:TBHS-21.JPG|800px|center]]
[[File:TBHS-21.JPG|800px|center]]



* Select the edges at the border of the upper face (holding {{KEY|CTRL}} ).
* Select the edges at the border of the upper face (holding {{KEY|CTRL}} ).
Line 180: Line 183:
[[File:TBHS-23.JPG|800px|center]]
[[File:TBHS-23.JPG|800px|center]]


* Add a [[File:PartDesign_Chamfer.svg|32px]] '''Chamfer''' of 1mm. This one is only aesthetic.

* Add a [[File:PartDesign_Chamfer.png|32px]] '''Chamfer''' of 1mm. This one is only aesthetic.


[[File:TBHS-22.JPG|800px|center]]
[[File:TBHS-22.JPG|800px|center]]


Tadaa!


== Export as a .STL ==
Tadaa !


== Export as a .STL ==
* In the Combo View on the left, select the tree view instead of the contextual task menu, click on the last feature (the chamfer).
* In the Combo View on the left, select the tree view instead of the contextual task menu, click on the last feature (the chamfer).


[[File:TBHS-24.JPG|800px|center]]
[[File:TBHS-24.JPG|800px|center]]



* Now you can select "Export..." from the File menu at the top left, and select the file format .STL.
* Now you can select "Export..." from the File menu at the top left, and select the file format .STL.
* Just print it :-)
* Just print it :-)


== Inspiration ==
== Inspiration ==

The above model make a good starting point to use FreeCAD, but as a toothbrush head stand it have its flaws : due to the print orientation and small surface the sticks are prone to break.
The above model make a good starting point to use FreeCAD, but as a toothbrush head stand it have its flaws : due to the print orientation and small surface the sticks are prone to break.


Line 203: Line 205:


[[File:TBHS-v2.jpg|800px|center]]
[[File:TBHS-v2.jpg|800px|center]]



Don't worry it is often needed to go through several revision for an idea (e.g. : once the prototype on the picture was used, we added more space between the heads so that they should not touch).
Don't worry it is often needed to go through several revision for an idea (e.g. : once the prototype on the picture was used, we added more space between the heads so that they should not touch).
Line 209: Line 210:
In this second part you will also learn to use more tools, like the powerful ''Linear repetition''.
In this second part you will also learn to use more tools, like the powerful ''Linear repetition''.


== Second idea : a band ==
== Second idea : a band ==


*Create a new document and select the [[Image:Workbench_PartDesign.png‎‎]] ''Part Design'' workbench.
*Create a new document and select the [[Image:Workbench_PartDesign.svg‎‎]] ''Part Design'' workbench.


=== Create a sketch ===
=== Create a sketch ===


*Create a [[Image:Sketcher_NewSketch.png|32px]] '''New sketch''', on the XY plan.
*Create a [[Image:Sketcher_NewSketch.svg|32px]] '''New sketch''', on the XY plane.

[[File:TBHS-1.JPG|800px|center]]
[[File:TBHS-1.JPG|800px|center]]


*Draw a [[Image:Sketcher_CreateSlot.svg|32px]] [[Sketcher_CreateSlot|'''Slot''']]

*Draw a [[Image:Sketcher_CreateSlot.png|32px]] [[Sketcher_Slot|'''Slot''']]
**Click to place the first center
**Click to place the first center
**Move to define the length and radius
**Move to define the length and radius
**Click to set the second center.
**Click to set the second center.
[[File:TBHS2-1.JPG|800px|center]]


[[File:TBHS2-1.JPG|800px|center]]


You now have a floating slot of unspecified dimensions.
You now have a floating slot of unspecified dimensions.


* Click on one of the horizontal line of the slot
* Click on one of the horizontal lines of the slot
* Click on [[File:Constraint_Length.png|32px]] [[Constraint_Length|'''Length''']]
* Click on [[File:Constraint_Length.png|32px]] [[Sketcher ConstrainDistance|'''Distance''']]
* A dialog prompts you to set a dimension. Enter 75mm, click OK.
* A dialog prompts you to set a dimension. Enter 75mm, click OK.
** that's for a 3 head stand, count 25mm for each, if you want more
** that's for a 3 head stand, count 25mm for each, if you want more
[[File:TBHS2-2.JPG|800px|center]]


[[File:TBHS2-2.JPG|800px|center]]


* Click on one point of the horizontal line
* Click on one point of the horizontal line
* Click on one point of the other horizontal line
* Click on one point of the other horizontal line
* Click on [[File:Constraint_Length.png|32px]] [[Constraint_Length|'''Length''']]
* Click on [[File:Constraint_Length.png|32px]] [[Sketcher_ConstrainDistance|'''Distance''']]
* A dialog prompts you to set a dimension. Enter 29mm, click OK.
* A dialog prompts you to set a dimension. Enter 29mm, click OK.

[[File:TBHS2-3.JPG|800px|center]]
[[File:TBHS2-3.JPG|800px|center]]


*Draw a [[Image:Sketcher_CreateSlot.svg|32px]] [[Sketcher_CreateSlot|'''Slot''']] around the first slot.


*Draw a [[Image:Sketcher_CreateSlot.png|32px]] [[Sketcher_Slot|'''Slot''']] around the first slot.
[[File:TBHS2-4.JPG|800px|center]]
[[File:TBHS2-4.JPG|800px|center]]


*Make the centers of the second slot coincident with the centers of the first slot with [[File:Constraint_PointOnPoint.svg|32px]] [[Sketcher ConstrainCoincident ‎|'''Coincident''']].


*Make the centers of the second slot coincident with the centers of the first slot with [[File:Constraint_PointOnPoint.png|32px]] [[Sketcher ConstrainCoincident ‎|'''Coincident''']].
[[File:TBHS2-5.JPG|800px|center]]
[[File:TBHS2-5.JPG|800px|center]]



* Click on one point of the horizontal line of the first slot
* Click on one point of the horizontal line of the first slot
* Click on one point of the nearest horizontal line of the second slot
* Click on one point of the nearest horizontal line of the second slot
* Click on [[File:Constraint_Length.png|32px]] [[Constraint_Length|'''Length''']]
* Click on [[File:Constraint_Length.png|32px]] [[Sketcher ConstrainDistance|'''Distance''']]
* A dialog prompts you to set a dimension. Enter 3mm, click OK.
* A dialog prompts you to set a dimension. Enter 3mm, click OK.

[[File:TBHS2-6.JPG|800px|center]]
[[File:TBHS2-6.JPG|800px|center]]



*To make the sketch fully constrained
*To make the sketch fully constrained
**Click on the lower left point of the second slot
**Click on the lower left point of the second slot
**Click on the origin of the XY plan
**Click on the origin of the XY plan
**Click on [[File:Constraint_PointOnPoint.png|32px]] [[Sketcher ConstrainCoincident ‎|'''Coincident''']]
**Click on [[File:Constraint_PointOnPoint.svg|32px]] [[Sketcher ConstrainCoincident ‎|'''Coincident''']]

[[File:TBHS2-7.JPG|800px|center]]
[[File:TBHS2-7.JPG|800px|center]]



* To leave the sketch, click either on the "Close" button on the left, or the [[File:Sketcher_LeaveSketch.png|32px]] icon in the toolbar, or press {{KEY|ESC}}.
* To leave the sketch, click either on the "Close" button on the left, or the [[File:Sketcher_LeaveSketch.png|32px]] icon in the toolbar, or press {{KEY|ESC}}.

[[File:TBHS2-8.JPG|800px|center]]
[[File:TBHS2-8.JPG|800px|center]]


=== Create a pad ===
=== Create a pad ===

* Click on [[Image:View-axometric.png|32px]] '''Axonometric''' among the standard views, to better see what will happen.
* Click on [[File:PartDesign_Pad.png|32px]] '''Pad'''.
* Click on [[Image:View-axometric.svg|32px]] '''Axonometric''' among the standard views, to better see what will happen.
* Click on [[File:PartDesign_Pad.svg|32px]] '''Pad'''.
* Enter 30mm and click OK.
* Enter 30mm and click OK.

[[File:TBHS2-9.JPG|800px|center]]
[[File:TBHS2-9.JPG|800px|center]]


=== Create a sketch on it ===


=== Create a sketch on it ===
*Select the upper face
*Select the upper face

[[File:TBHS2-10.JPG|800px|center]]
[[File:TBHS2-10.JPG|800px|center]]


*Create a [[Image:Sketcher_NewSketch.svg|32px]] '''New sketch'''. As a face was selected it will not ask you to choose a plane.


*Create a [[Image:Sketcher_NewSketch.png|32px]] '''New sketch'''. As a face was selected it will not ask you to choose a plane.
[[File:TBHS2-11.JPG|800px|center]]
[[File:TBHS2-11.JPG|800px|center]]


*Draw an [[Image:Sketcher_CreateHexagon.svg|32px]] [[Sketcher_CreateHexagon|'''Hexagon''']]

*Draw an [[Image:Sketcher_CreateHexagon.png|32px]] [[Sketcher_Hexagon|'''Hexagon''']]
**Click to place the center
**Click to place the center
**Move to define the radius
**Move to define the radius
**Click to set
**Click to set

[[File:TBHS2-12.JPG|800px|center]]
[[File:TBHS2-12.JPG|800px|center]]



*Click on an edge of the hexagon
*Click on an edge of the hexagon
*Click on [[Image:Constraint_Horizontal.png|32px]] [[Sketcher ConstrainHorizontal ‎|'''Horizontal''']]
*Click on [[Image:Constraint_Horizontal.svg|32px]] [[Sketcher ConstrainHorizontal ‎|'''Horizontal''']]
[[File:TBHS2-13.JPG|800px|center]]
[[File:TBHS2-13.JPG|800px|center]]


Line 297: Line 301:
* Click on the center of the hexagon
* Click on the center of the hexagon
* Click on the horizontal line of the XY plane
* Click on the horizontal line of the XY plane
* Click on [[File:Constraint_Length.png|32px]] [[Constraint_Length|'''Length''']]
* Click on [[File:Constraint_Length.png|32px]] [[Sketcher ConstrainDistance|'''Distance''']]
* A dialog prompts you to set a dimension. Enter 15mm, click OK.
* A dialog prompts you to set a dimension. Enter 15mm, click OK.

[[File:TBHS2-14.JPG|800px|center]]
[[File:TBHS2-14.JPG|800px|center]]



* Click on the center of the hexagon
* Click on the center of the hexagon
* Click on the vertical of the XY plane
* Click on the vertical of the XY plane
* Click on [[File:Constraint_Length.png|32px]] [[Constraint_Length|'''Length''']]
* Click on [[File:Constraint_Length.png|32px]] [[Sketcher ConstrainDistance|'''Distance''']]
* A dialog prompts you to set a dimension. Enter 10mm, click OK.
* A dialog prompts you to set a dimension. Enter 10mm, click OK.

[[File:TBHS2-15.JPG|800px|center]]
[[File:TBHS2-15.JPG|800px|center]]



* Click on the blue circle of the hexagon
* Click on the blue circle of the hexagon
* Click on [[File:Constraint_Radius.png|32px]] [[Constraint_Radius|'''Radius''']]
* Click on [[File:Sketcher_ConstrainRadius.svg|32px]] [[Sketcher ConstrainRadius|'''Radius''']]
* A dialog prompts you to set a dimension. Enter 8mm, click OK.
* A dialog prompts you to set a dimension. Enter 8mm, click OK.

[[File:TBHS2-16.JPG|800px|center]]
[[File:TBHS2-16.JPG|800px|center]]



* To leave the sketch, click either on the "Close" button on the left, or the [[File:Sketcher_LeaveSketch.png|32px]] icon in the toolbar, or press {{KEY|ESC}}.
* To leave the sketch, click either on the "Close" button on the left, or the [[File:Sketcher_LeaveSketch.png|32px]] icon in the toolbar, or press {{KEY|ESC}}.

[[File:TBHS2-17.JPG|800px|center]]
[[File:TBHS2-17.JPG|800px|center]]


=== Create a hole ===
=== Create a hole ===

* Click on [[Image:View-axometric.png|32px]] '''Axonometric''' among the standard views, to better see what will happen.
* Click on [[File:PartDesign_Pocket.png|32px]] [[PartDesign_Pocket|'''Pocket''']].
* Click on [[Image:View-axometric.svg|32px]] '''Axonometric''' among the standard views, to better see what will happen.
* Click on [[File:PartDesign_Pocket.svg|32px]] [[PartDesign_Pocket|'''Pocket''']].
* Select ''to the first'' in the dropdown menu and click OK.
* Select ''to the first'' in the dropdown menu and click OK.

[[File:TBHS2-18.JPG|800px|center]]
[[File:TBHS2-18.JPG|800px|center]]


=== Linear repetition ===


=== Linear repetition ===
* In the Combo View on the left, select the tree view instead of the contextual task menu, click on the pocket feature.
* In the Combo View on the left, select the tree view instead of the contextual task menu, click on the pocket feature.
* Click on [[File:PartDesign_LinearPattern.png|32px]] [[PartDesign_LinearPattern|'''LinearPattern''']].
* Click on [[File:PartDesign_LinearPattern.svg|32px]] [[PartDesign_LinearPattern|'''LinearPattern''']].
* Set the length at 55mm and occurencies at 3, then click OK.
* Set the length at 55mm and occurencies at 3, then click OK.

[[File:TBHS2-19.JPG|800px|center]]
[[File:TBHS2-19.JPG|800px|center]]


=== Create a sketch on it ===
=== Create a sketch on it ===

*Select the inner face
*Select the inner face

[[File:TBHS2-20.JPG|800px|center]]
[[File:TBHS2-20.JPG|800px|center]]


*Create a [[Image:Sketcher_NewSketch.svg|32px]] '''New sketch'''. As a face was selected it will not ask you to choose a plane.


*Create a [[Image:Sketcher_NewSketch.png|32px]] '''New sketch'''. As a face was selected it will not ask you to choose a plane.
[[File:TBHS2-21.JPG|800px|center]]
[[File:TBHS2-21.JPG|800px|center]]


* Click on [[File:Sketcher_Circle.svg|32px]] [[Sketcher_CreateCircle|'''Circle''']], click to place the center, move the pointer and click to define the radius.


* Click on [[File:Sketcher_Circle.png|32px]] [[Sketcher_Circle|'''Circle''']], click to place the center, move the pointer and click to define the radius.
[[File:TBHS2-22.JPG|800px|center]]
[[File:TBHS2-22.JPG|800px|center]]



* Click on the center of the circle
* Click on the center of the circle
* Click on the horizontal line of the XY plane
* Click on the horizontal line of the XY plane
* Click on [[File:Constraint_Length.png|32px]] [[Constraint_Length|'''Length''']]
* Click on [[File:Constraint_Length.png|32px]] [[Sketcher ConstrainDistance|'''Distance''']]
* A dialog prompts you to set a dimension. Enter 15mm, click OK.
* A dialog prompts you to set a dimension. Enter 15mm, click OK.
[[File:TBHS2-23.JPG|800px|center]]


[[File:TBHS2-23.JPG|800px|center]]


* Click on the center of the circle
* Click on the center of the circle
* Click on the vertical of the XY plane
* Click on the vertical of the XY plane
* Click on [[File:Constraint_Length.png|32px]] [[Constraint_Length|'''Length''']]
* Click on [[File:Constraint_Length.png|32px]] [[Sketcher ConstrainDistance|'''Distance''']]
* A dialog prompts you to set a dimension. Enter 10mm, click OK.
* A dialog prompts you to set a dimension. Enter 10mm, click OK.
[[File:TBHS2-24.JPG|800px|center]]


[[File:TBHS2-24.JPG|800px|center]]


* Click on the circle
* Click on the circle
* Click on [[File:Constraint_Radius.png|32px]] [[Constraint_Radius|'''Radius''']]
* Click on [[File:Sketcher_ConstrainRadius.svg|32px]] [[Sketcher ConstrainRadius|'''Radius''']]
* A dialog prompts you to set a dimension. Enter 3.5mm, click OK.
* A dialog prompts you to set a dimension. Enter 3.5mm, click OK.

[[File:TBHS2-25.JPG|800px|center]]
[[File:TBHS2-25.JPG|800px|center]]



* To leave the sketch, click either on the "Close" button on the left, or the [[File:Sketcher_LeaveSketch.png|32px]] icon in the toolbar, or press {{KEY|ESC}}.
* To leave the sketch, click either on the "Close" button on the left, or the [[File:Sketcher_LeaveSketch.png|32px]] icon in the toolbar, or press {{KEY|ESC}}.

[[File:TBHS2-26.JPG|800px|center]]
[[File:TBHS2-26.JPG|800px|center]]


=== Create a pad ===


* Click on [[Image:View-axometric.svg|32px]] '''Axonometric''' among the standard views, to better see what will happen.
=== Create a pad ===
* Click on [[Image:View-axometric.png|32px]] '''Axonometric''' among the standard views, to better see what will happen.
* Click on [[File:PartDesign_Pad.svg|32px]] '''Pad'''.
* Click on [[File:PartDesign_Pad.png|32px]] '''Pad'''.
* Enter 4mm and click OK.
* Enter 4mm and click OK.

[[File:TBHS2-27.JPG|800px|center]]
[[File:TBHS2-27.JPG|800px|center]]


=== Linear repetition ===
=== Linear repetition ===

* In the Combo View on the left, select the tree view instead of the contextual task menu, click on the pad feature.
* In the Combo View on the left, select the tree view instead of the contextual task menu, click on the pad feature.
* Click on [[File:PartDesign_LinearPattern.png|32px]] [[PartDesign_LinearPattern|'''LinearPattern''']].
* Click on [[File:PartDesign_LinearPattern.svg|32px]] [[PartDesign_LinearPattern|'''LinearPattern''']].
* Set the length at 55mm and occurencies at 3, then click OK.
* Set the length at 55mm and occurencies at 3, then click OK.

[[File:TBHS2-28.JPG|800px|center]]
[[File:TBHS2-28.JPG|800px|center]]


=== Draft ===


=== Draft ===
*Select the side of each round pads
*Select the side of each round pads

[[File:TBHS2-29.JPG|800px|center]]
[[File:TBHS2-29.JPG|800px|center]]


* Click on [[File:PartDesign_Draft.svg|32px]] [[PartDesign_Draft|'''Draft''']].

* Click on [[File:PartDesign_Draft.png|32px]] [[PartDesign_Draft|'''Draft''']].
* Set the draft angle at 40°.
* Set the draft angle at 40°.
* Click on "Neutral plane" and select the face on which the sketch is drawn.
* Click on "Neutral plane" and select the face on which the sketch is drawn.
* Tick "Invert the draft direction".
* Tick "Invert the draft direction".
[[File:TBHS2-30.JPG|800px|center]]


[[File:TBHS2-30.JPG|800px|center]]


We could have used a chamfer to do something similar, but the draft is more appropriate in this case.
We could have used a chamfer to do something similar, but the draft is more appropriate in this case.
Line 399: Line 412:
[[File:TBHS2-30-chamfer.JPG|200px]][[File:TBHS2-30-draft.JPG|200px]]
[[File:TBHS2-30-chamfer.JPG|200px]][[File:TBHS2-30-draft.JPG|200px]]


=== Finishes ===


=== Finitions ===
*Holding {{KEY|CTRL}} select the bottom and top faces.
*Holding {{KEY|CTRL}} select the bottom and top faces.

[[File:TBHS2-31-bottom.JPG|200px]][[File:TBHS2-31-top.JPG|200px]]
[[File:TBHS2-31-bottom.JPG|200px]][[File:TBHS2-31-top.JPG|200px]]


** Add a [[File:PartDesign_Chamfer.png|32px]] '''Chamfer''' of 0,5mm.
** Add a [[File:PartDesign_Chamfer.svg|32px]] '''Chamfer''' of 0,5mm.

[[File:TBHS2-31.JPG|800px|center]]
[[File:TBHS2-31.JPG|800px|center]]


Perfect!


== Export as a .STL ==
Perfect !


== Export as a .STL ==
* In the Combo View on the left, select the tree view instead of the contextual task menu, click on the last feature (the chamfer).
* In the Combo View on the left, select the tree view instead of the contextual task menu, click on the last feature (the chamfer).


[[File:TBHS2-32.JPG|800px|center]]
[[File:TBHS2-32.JPG|800px|center]]



* Now you can select "Export..." from the File menu at the top left, and select the file format .STL.
* Now you can select "Export..." from the File menu at the top left, and select the file format .STL.
Line 420: Line 434:




{{PartDesign Tools navi{{#translation:}}}}
{{clear}}
{{Sketcher Tools navi{{#translation:}}}}
{{Userdocnavi{{#translation:}}}}

Latest revision as of 20:22, 25 February 2024

Tutorial
Topic
Modeling
Level
Beginner
Time to complete
1 hour
Authors
EmmanuelG
FreeCAD version
0.16 or greater
Example files
Thingiverse 2403310
See also
None

A daily-life problem

Periuțele electrice de dinți mai rar vin cu un suport pentru cap, în timp ce într-o familie, veți vedea adesea mai multe capete folosite cu un singur corp. Mulți oameni se confruntă cu o problemă comună, ceea ce duce la o varietate de soluții, după cum puteți vedea pe Thingiverse (200 la 800 de proiecte sunt legate de acest lucru). Iată primul răspuns și cum să îl proiectăm.

This tutorial will take you through the steps needed to model the part shown in the image below using basic tools from the Part Design Workbench (many of the tools and capabilities are not covered).

First idea : a plate

First idea : a plate

  • From the start-page, select Part Design, or create a new document and select the Part Design workbench.

Create a sketch

  • Click on New sketch. Either from the contextual task menu at the left, or the toolbar above or from the Part Design menu at the top.

A dialog prompts you to choose the sketch orientation and provide an offset.

  • We will pick the XY Plane as shown in the image above (that orientation correspond to the common build plate of most 3D printers), then click OK.

You now are facing the XY plane from above, and have access to the drawing tools.

  • Click on Rectangle.
  • Click to place a first point.
  • Click to place the opposite corner.
  • Press ESC or click the right mouse button to stop using the tool.

You now have a floating rectangle of unspecified dimensions.

  • Click on a line of the rectangle, you now have access to the constraint tools at the right of the toolbar (depending of the size of your screen you may need to drag them to the left in order to see them all)
  • Click on Distance
  • A dialog prompts you to set a dimension. Enter 80mm, click OK.
  • Repeat with the other side of the rectangle, also 80mm.

You now have a floating square.

  • Click on the lower left point of the square.
  • Click on the origin of the XY plane (at the intersection of the two thick lines).
  • Click on Coincident.

You now have a totally constrained sketch, as you are told by the solver on the left and the change of color. It is a good practice to always have a totally constrained sketch.

An under-constrained sketch can leave room for unwanted change, if you modify something later on.

On the opposite, an over-constrained sketch is also not good. In that case the solver warn you of redundant constraints and you should remove some of them.

  • To leave the sketch, click either on the "Close" button on the left, or the icon in the toolbar, or press ESC.

You now only see the square, and the contextual task menu on the left show you more options than before.

Create a pad

  • Click on Axonometric among the standard views, to better see what will happen.
  • Click on Pad.
  • Enter 4mm and click OK.

Your sketch is now in volume!

Create a sketch on it

  • Select the upper face

The color of the face change and you have more options in the contextual task menu.

  • Click on New sketch. As a face was selected it will not ask you to choose a plane.
  • Click on Circle, click to place the center, move the pointer and click to define the radius.
  • Draw 4 circles on the pad (of any size)
  • Press ESC or click the right mouse button to stop using the tool.

Now the circles share the same radius.

  • Click on External geometry.
  • Click on the four sides of the square, it add lines, color magenta.

Theses lines will serve as reference to position the circles.

  • Click on Distance.
  • Click on a center of a circle.
  • Click on a magenta line.
  • Set distance (20mm from each side).
  • Click on a circle
  • Click on Radius and set it at 1,5mm.
  • To leave the sketch, click either on the "Close" button on the left, or the icon in the toolbar, or press ESC.

Create a pad

  • Click on Axonometric among the standard views, to better see what will happen.
  • Click on Pad.
  • Enter 25mm and click OK.

You have the basic shape, it just need final touches.

Rounding the corners

  • Holding CTRL click on the vertical edge at each corner to select the four of them.

Don't hesitate to help you by switching the display mode (just at the left of the Axonometric View) between Wireframe and Wireframe and shadow.

  • Click on Fillet.
  • Set the radius at 20mm.

Much better.

Making it more robust

We need to add material at the base of the cylinders to make them less prone to snap. Because of the printing orientation these small surfaces will be fragile at the junction with the base.
  • Select the circles at the base of the cylinders

Chamfer the edges

  • Select the face under the base, add a Chamfer of 0,5mm.

The first layer of plastic is often being squashed a little too much, this will compensate that and save you time in cleaning the model. If the first layer is ok that will make it only nicer

  • Select the edges at the border of the upper face (holding CTRL ).
  • Add a Chamfer of 1mm. This one is only aesthetic.

Tadaa!

Export as a .STL

  • In the Combo View on the left, select the tree view instead of the contextual task menu, click on the last feature (the chamfer).
  • Now you can select "Export..." from the File menu at the top left, and select the file format .STL.
  • Just print it :-)

Inspiration

The above model make a good starting point to use FreeCAD, but as a toothbrush head stand it have its flaws : due to the print orientation and small surface the sticks are prone to break.

Inspired by the variety of solutions other people came up with, we will make this second version which will be much better.

Don't worry it is often needed to go through several revision for an idea (e.g. : once the prototype on the picture was used, we added more space between the heads so that they should not touch).

In this second part you will also learn to use more tools, like the powerful Linear repetition.

Second idea : a band

  • Create a new document and select the Part Design workbench.

Create a sketch

  • Create a New sketch, on the XY plane.
  • Draw a Slot
    • Click to place the first center
    • Move to define the length and radius
    • Click to set the second center.

You now have a floating slot of unspecified dimensions.

  • Click on one of the horizontal lines of the slot
  • Click on Distance
  • A dialog prompts you to set a dimension. Enter 75mm, click OK.
    • that's for a 3 head stand, count 25mm for each, if you want more
  • Click on one point of the horizontal line
  • Click on one point of the other horizontal line
  • Click on Distance
  • A dialog prompts you to set a dimension. Enter 29mm, click OK.
  • Draw a Slot around the first slot.
  • Make the centers of the second slot coincident with the centers of the first slot with Coincident.
  • Click on one point of the horizontal line of the first slot
  • Click on one point of the nearest horizontal line of the second slot
  • Click on Distance
  • A dialog prompts you to set a dimension. Enter 3mm, click OK.
  • To make the sketch fully constrained
    • Click on the lower left point of the second slot
    • Click on the origin of the XY plan
    • Click on Coincident
  • To leave the sketch, click either on the "Close" button on the left, or the icon in the toolbar, or press ESC.

Create a pad

  • Click on Axonometric among the standard views, to better see what will happen.
  • Click on Pad.
  • Enter 30mm and click OK.

Create a sketch on it

  • Select the upper face
  • Create a New sketch. As a face was selected it will not ask you to choose a plane.
  • Draw an Hexagon
    • Click to place the center
    • Move to define the radius
    • Click to set
  • Click on an edge of the hexagon
  • Click on Horizontal


  • Click on the center of the hexagon
  • Click on the horizontal line of the XY plane
  • Click on Distance
  • A dialog prompts you to set a dimension. Enter 15mm, click OK.
  • Click on the center of the hexagon
  • Click on the vertical of the XY plane
  • Click on Distance
  • A dialog prompts you to set a dimension. Enter 10mm, click OK.
  • Click on the blue circle of the hexagon
  • Click on Radius
  • A dialog prompts you to set a dimension. Enter 8mm, click OK.
  • To leave the sketch, click either on the "Close" button on the left, or the icon in the toolbar, or press ESC.

Create a hole

  • Click on Axonometric among the standard views, to better see what will happen.
  • Click on Pocket.
  • Select to the first in the dropdown menu and click OK.

Linear repetition

  • In the Combo View on the left, select the tree view instead of the contextual task menu, click on the pocket feature.
  • Click on LinearPattern.
  • Set the length at 55mm and occurencies at 3, then click OK.

Create a sketch on it

  • Select the inner face
  • Create a New sketch. As a face was selected it will not ask you to choose a plane.
  • Click on Circle, click to place the center, move the pointer and click to define the radius.
  • Click on the center of the circle
  • Click on the horizontal line of the XY plane
  • Click on Distance
  • A dialog prompts you to set a dimension. Enter 15mm, click OK.
  • Click on the center of the circle
  • Click on the vertical of the XY plane
  • Click on Distance
  • A dialog prompts you to set a dimension. Enter 10mm, click OK.
  • Click on the circle
  • Click on Radius
  • A dialog prompts you to set a dimension. Enter 3.5mm, click OK.
  • To leave the sketch, click either on the "Close" button on the left, or the icon in the toolbar, or press ESC.

Create a pad

  • Click on Axonometric among the standard views, to better see what will happen.
  • Click on Pad.
  • Enter 4mm and click OK.

Linear repetition

  • In the Combo View on the left, select the tree view instead of the contextual task menu, click on the pad feature.
  • Click on LinearPattern.
  • Set the length at 55mm and occurencies at 3, then click OK.

Draft

  • Select the side of each round pads
  • Click on Draft.
  • Set the draft angle at 40°.
  • Click on "Neutral plane" and select the face on which the sketch is drawn.
  • Tick "Invert the draft direction".

We could have used a chamfer to do something similar, but the draft is more appropriate in this case.

Chamfer = left / Draft = right

Finishes

  • Holding CTRL select the bottom and top faces.

    • Add a Chamfer of 0,5mm.

Perfect!

Export as a .STL

  • In the Combo View on the left, select the tree view instead of the contextual task menu, click on the last feature (the chamfer).
  • Now you can select "Export..." from the File menu at the top left, and select the file format .STL.
  • Print it instead of the first version or to replace it if it eventually broke ;-)