Difference between revisions of "Sketcher Workbench/zh-tw"
Kejuchenshi (talk | contribs) (Created page with "速寫坊") |
(Updating to match new version of source page) |
||
(33 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
− | [[ | + | <languages/> |
+ | {{Docnav | ||
+ | |[[Ship Workbench|Ship Workbench]] | ||
+ | |[[Spreadsheet Workbench|Spreadsheet Workbench]] | ||
+ | |IconL=Workbench_Ship.svg | ||
+ | |IconR=Workbench_Spreadsheet.svg | ||
+ | }} | ||
+ | |||
+ | [[Image:Workbench_Sketcher.svg|64px]] | ||
+ | |||
+ | == Introduction == | ||
− | + | <div class="mw-translate-fuzzy"> | |
− | + | '''速寫坊''' 是用於創建平面幾何給 '''[[PartDesign Workbench|零件坊]]''' 以及其他工作坊。一般而言平面幾何被視為大部分 CAD 模型起點。簡易平面草稿0可以"擠出"為立體形狀，進一步平面草稿可在立體表面開口，且草稿可在立體物表面定義'路徑 （擠出）'。搭配 [[Part Module|布林運算]] 草稿形塑原創 solid shape 設計核心。 | |
− | + | </div> | |
− | The Sketcher workbench | + | The Sketcher workbench features "constraints", allowing 2D shapes to follow precise geometrical definitions in terms of length, angles, and relationships (horizontality, verticality, perpendicularity, etc.). A constraint solver calculates the constrained-extent of 2D geometry and allows interactive exploration of degrees-of-freedom of the sketch. |
− | |||
− | + | {{TOCright}} | |
+ | [[File:FC_ConstrainedSketch.png|none]] | ||
+ | |||
+ | {{Caption|A fully constrained sketch}} | ||
+ | |||
+ | == Basics of constraint sketching == | ||
To explain how the Sketcher works, it may be useful to compare it to the "traditional" way of drafting. | To explain how the Sketcher works, it may be useful to compare it to the "traditional" way of drafting. | ||
Line 26: | Line 40: | ||
There are two kinds of constraints: geometric and dimensional. They are detailed in the [[#The tools|'The tools']] section below. | There are two kinds of constraints: geometric and dimensional. They are detailed in the [[#The tools|'The tools']] section below. | ||
− | === What the Sketcher is not good for === | + | ==== What the Sketcher is not good for ==== |
The Sketcher is not intended for producing 2D blueprints. Once sketches are used to generate a solid feature, they are automatically hidden. Constraints are only visible in Sketch edit mode. | The Sketcher is not intended for producing 2D blueprints. Once sketches are used to generate a solid feature, they are automatically hidden. Constraints are only visible in Sketch edit mode. | ||
− | If you only need to produce 2D views for print, and don't want to create 3D models, check out the [[Draft Module|Draft workbench]] | + | If you only need to produce 2D views for print, and don't want to create 3D models, check out the [[Draft Module|Draft workbench]]. Unlike Sketcher elements, Draft objects don't use constraints; they are simple shapes defined at the moment of creation. Both Draft and Sketcher can be used for 2D geometry drawing, and 3D solid creation, although their preferred use is different; the Sketcher is normally used together with [[Part Workbench|Part]] and [[PartDesign Workbench|PartDesign]] to create solids; Draft is normally used for simple planar drawings over a grid, as when drawing an architectural floor plan; in these situations Draft is mostly used together with the [[Arch Workbench|Arch Workbench]]. The tool [[Draft Draft2Sketch|Draft2Sketch]] converts a Draft object to a Sketch object, and vice versa; many tools that require a 2D element as input work with either type of object as an internal conversion is done automatically. |
− | + | == Sketching Workflow == | |
A Sketch is always 2-dimensional (2D). To create a solid, a 2D Sketch of a single enclosed area is created and then either Padded or Revolved to add the 3rd dimension, creating a 3D solid from the 2D Sketch. | A Sketch is always 2-dimensional (2D). To create a solid, a 2D Sketch of a single enclosed area is created and then either Padded or Revolved to add the 3rd dimension, creating a 3D solid from the 2D Sketch. | ||
− | If | + | If a Sketch has segments that cross one another, places where a Point is not directly on a segment, or places where there are gaps between endpoints of adjacent segments, Pad or Revolve won't create a solid. Sometimes a Sketch which contains lines which cross one another will work for a simple operation such as Pad, but later operations such as Linear Pattern will fail. It is best to avoid crossing lines. The exception to this rule is that it doesn't apply to Construction (blue) Geometry. |
Inside the enclosed area we can have smaller non-overlapping areas. These will become voids when the 3D solid is created. | Inside the enclosed area we can have smaller non-overlapping areas. These will become voids when the 3D solid is created. | ||
− | + | Once a Sketch is fully constrained, the Sketch features will turn green; Construction Geometry will remain blue. It is usually "finished" at this point and suitable for use in creating a 3D solid. However, once the Sketch dialog is closed it may be worthwhile going to [[Part Workbench|Part Workbench]] and running [[Part CheckGeometry|Check geometry]] to ensure there are no features in the Sketch which may cause later problems. | |
− | The Sketcher Workbench tools are all located in the | + | |
+ | == The tools == | ||
+ | The Sketcher Workbench tools are all located in the Sketch menu that appears when you load the Sketcher Workbench. | ||
+ | |||
+ | * [[Image:Sketcher_NewSketch.svg|32px]] [[Sketcher_NewSketch|New sketch]]: Creates a new sketch on a selected face or plane. If no face is selected while this tool is executed the user is prompted to select a plane from a pop-up window. | ||
+ | |||
+ | * [[Image:Sketcher_EditSketch.svg|32px]] [[Sketcher_EditSketch|Edit sketch]]: Edit the selected Sketch. This will open the [[Sketcher Dialog|Sketcher Dialog]]. | ||
+ | |||
+ | * [[Image:Sketcher_LeaveSketch.svg|32px]] [[Sketcher_LeaveSketch|Leave sketch]]: Leave the Sketch editing mode. | ||
+ | |||
+ | * [[Image:Sketcher_ViewSketch.svg|32px]] [[Sketcher_ViewSketch|View sketch]]: Sets the model view perpendicular to the sketch plane. | ||
+ | |||
+ | * [[Image:Sketcher ViewSection.svg|32px]] [[Sketcher_ViewSection|View section]]: Creates a section plane that temporarily hides any matter in front of the sketch plane. {{Version|0.18}} | ||
+ | |||
+ | * [[Image:Sketcher_MapSketch.svg|32px]] [[Sketcher_MapSketch|Map sketch to face]]: Maps a sketch to the previously selected face of a solid. | ||
+ | |||
+ | * [[Sketcher_Reorient|Reorient sketch ]]: Allows you to change the position of a sketch | ||
+ | |||
+ | * [[Sketcher_ValidateSketch|Validate sketch]]: Verify the tolerance of different points and adjust them. | ||
+ | |||
+ | * [[Image:Sketcher MergeSketch.svg|32px]] [[Sketcher MergeSketches|Merge sketches]]: Merge two or more sketches. {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Sketcher MirrorSketch.svg|32px]] [[Sketcher MirrorSketch|Mirror sketch]]: Mirror a sketch along the x-axis, the y-axis or the origin. {{Version|0.16}} | ||
+ | |||
+ | ===Sketcher geometries=== | ||
+ | |||
+ | These are tools for creating objects. | ||
+ | |||
+ | * [[Image:Sketcher_CreatePoint.svg|32px]] [[Sketcher_CreatePoint|Point]]: Draws a point. | ||
+ | |||
+ | * [[Image:Sketcher_Line.svg|32px]] [[Sketcher_CreateLine|Line]]: Draws a line segment between 2 points. Lines are infinite regarding certain constraints. | ||
+ | |||
+ | * [[Image:Sketcher_CompCreateArc.png|48px]] [[Sketcher_CompCreateArc|Create an arc]]: This is an icon menu in the Sketcher toolbar that holds the following commands: | ||
+ | |||
+ | :* [[Image:Sketcher_Arc.svg|32px]] [[Sketcher_CreateArc|Arc]]: Draws an arc segment from center, radius, start angle and end angle. | ||
+ | |||
+ | :* [[Image:Sketcher_Create3PointArc.svg|32px]] [[Sketcher_Create3PointArc|Arc by 3 points]]: Draws an arc segment from two endpoints and another point on the circumference. | ||
+ | |||
+ | * [[Image:Sketcher_CompCreateCircle.png|48px]] [[Sketcher_CompCreateCircle|Create a circle]]: This is an icon menu in the Sketcher toolbar that holds the following commands: | ||
+ | |||
+ | :* [[Image:Sketcher_Circle.svg|32px]] [[Sketcher_CreateCircle|Circle]]: Draws a circle from center and radius. | ||
+ | |||
+ | :* [[Image:Sketcher_Create3PointCircle.svg|32px]] [[Sketcher_Create3PointCircle|Circle by 3 points]]: Draws a circle from three points on the circumference. | ||
+ | |||
+ | * [[Image:Sketcher_CompCreateConic.png|48px]] [[Sketcher_CompCreateConic|Create a conic]]: The sketcher provides the following conical sections. Unlike B-splines they can be used with all sorts of constraints such as tangents, point-on-object, or orthogonal. | ||
+ | ** [[Image:Sketcher_CreateEllipse.svg|32px]] [[Sketcher CreateEllipseByCenter|Ellipse by center]]: Draws an ellipse by center point, major radius point and minor radius point. {{Version|0.15}} | ||
+ | ** [[Image:Sketcher_CreateEllipse_3points.svg|32px]] [[Sketcher CreateEllipseBy3Points|Ellipse by 3 points]]: Draws an ellipse by major diameter (2 points) and minor radius point. {{Version|0.15}} | ||
+ | ** [[Image:Sketcher_Elliptical_Arc.svg|32px]] [[Sketcher_CreateArcOfEllipse|Arc of ellipse]]: Draws an arc of ellipse by center point, major radius point, starting point and ending point. {{Version|0.15}} | ||
+ | **[[Image:Sketcher_Hyperbolic_Arc.svg|32px]] [[Sketcher_CreateArcOfHyperbola|Arc of hyperbola]]: Draws an arc of hyperbola. {{Version|0.17}} | ||
+ | **[[Image:Sketcher_Parabolic_Arc.svg|32px]] [[Sketcher_CreateArcOfParabola|Arc of parabola]]: Draws an arc of parabola. {{Version|0.17}} | ||
+ | |||
+ | * [[Image:Sketcher_CompCreateBSpline.png|48px]] [[Sketcher_CompCreateBSpline|Create a B-spline]]: This is an icon menu in the Sketcher toolbar that holds the following commands: | ||
+ | ** [[File:Sketcher_CreateBSpline.svg|32px]] [[Sketcher_CreateBSpline|Create B-spline]]: Draws a B-spline curve by its control points. {{Version|0.17}} | ||
+ | ** [[File:Sketcher_Create_Periodic_BSpline.svg|32px]] [[Sketcher_CreatePeriodicBSpline|Create periodic B-spline]]: Draws a periodic (closed) B-spline curve by its control points. {{Version|0.17}} | ||
− | + | * [[Image:Sketcher_CreatePolyline.svg|32px]] [[Sketcher_CreatePolyline|Polyline (multiple-point line)]]: Draws a line made of multiple line segments. Pressing the M key while drawing a Polyline toggles between the different polyline modes. | |
− | === Best Practices | + | * [[Image:Sketcher_CreateRectangle.svg|32px]] [[Sketcher_CreateRectangle|Rectangle]]: Draws a rectangle from 2 opposite points. |
+ | |||
+ | * [[Image:Sketcher_CompCreateRegularPolygon.png|48px]] [[Sketcher_CompCreateRegularPolygon|Create regular polygon]]: This is an icon menu in the Sketcher toolbar that holds the following commands: | ||
+ | |||
+ | :* [[Image:Sketcher_CreateTriangle.svg|32px]] [[Sketcher_CreateTriangle|Triangle]]: Draws a regular triangle inscribed in a construction geometry circle. {{Version|0.15}} | ||
+ | |||
+ | :* [[Image:Sketcher_CreateSquare.svg|32px]] [[Sketcher_CreateSquare|Square]]: Draws a regular square inscribed in a construction geometry circle. {{Version|0.15}} | ||
+ | |||
+ | :* [[Image:Sketcher_CreatePentagon.svg|32px]] [[Sketcher_CreatePentagon|Pentagon]]: Draws a regular pentagon inscribed in a construction geometry circle. {{Version|0.15}} | ||
+ | |||
+ | :* [[Image:Sketcher_CreateHexagon.svg|32px]] [[Sketcher_CreateHexagon|Hexagon]]: Draws a regular hexagon inscribed in a construction geometry circle. {{Version|0.15}} | ||
+ | |||
+ | :* [[Image:Sketcher_CreateHeptagon.svg|32px]] [[Sketcher_CreateHeptagon|Heptagon]]: Draws a regular heptagon inscribed in a construction geometry circle. {{Version|0.15}} | ||
+ | |||
+ | :* [[Image:Sketcher_CreateOctagon.svg|32px]] [[Sketcher_CreateOctagon|Octagon]]: Draws a regular octagon inscribed in a construction geometry circle. {{Version|0.15}} | ||
+ | |||
+ | :* [[Image:Sketcher_CreateRegularPolygon.svg|32px]] [[Sketcher_CreateRegularPolygon|Create Regular Polygon]] : Draws a regular polygon by selecting the number of sides and picking two points: the center and one corner. | ||
+ | |||
+ | * [[Image:Sketcher_CreateSlot.png|32px]] [[Sketcher_CreateSlot|Slot]]: Draws an oval by selecting the center of one semicircle and an endpoint of the other semicircle. | ||
+ | |||
+ | * [[Image:Sketcher_CreateFillet.svg|32px]] [[Sketcher_CreateFillet|Fillet]]: Makes a fillet between two lines joined at one point. Select both lines or click on the corner point, then activate the tool. | ||
+ | |||
+ | * [[Image:Sketcher_Trimming.svg|32px]] [[Sketcher_Trimming|Trimming]]: Trims a line, circle or arc with respect to the clicked point. | ||
+ | |||
+ | * [[File:Sketcher_Extend.svg|32px]] [[Sketcher_Extend|Extend]]: Extends a line or an arc to a boundary line, arc, ellipse, arc of ellipse or a point in space. {{Version|0.17}} | ||
+ | |||
+ | * [[Image:Sketcher_External.svg|32px]] [[Sketcher_External|External Geometry]]: Creates an edge linked to external geometry. | ||
+ | |||
+ | * [[File:Sketcher_CarbonCopy.svg|32px]] [[Sketcher_CarbonCopy|CarbonCopy]]: Copies the geometry of another sketch. {{Version|0.17}} | ||
+ | |||
+ | * [[File:Sketcher AlterConstruction.svg|32px]] [[Sketcher_ToggleConstruction|Construction Mode]]: Toggles sketch geometry from/to construction mode. Construction geometry is shown in blue and is discarded outside of Sketch editing mode. | ||
+ | |||
+ | ===Sketcher constraints=== | ||
+ | |||
+ | Constraints are used to define lengths, set rules between sketch elements, and to lock the sketch along the vertical and horizontal axes. Some constraints require use of [[Sketcher_helper_constraint|Helper constraints]]. | ||
+ | |||
+ | ====Geometric constraints==== | ||
+ | These constraints are not associated with numeric data. | ||
+ | |||
+ | * [[Image:Constraint_PointOnPoint.svg|32px]] [[Sketcher ConstrainCoincident|Coincident]]: Affixes a point onto (coincident with) one or more other points. | ||
+ | |||
+ | * [[Image:Constraint_PointOnObject.svg|32px]] [[Sketcher ConstrainPointOnObject|Point On Object]]: Affixes a point onto another object such as a line, arc, or axis. | ||
+ | |||
+ | * [[Image:Constraint_Vertical.svg|32px]] [[Sketcher_ConstrainVertical|Vertical]]: Constrains the selected lines or polyline elements to a true vertical orientation. More than one object can be selected before applying this constraint. | ||
+ | |||
+ | * [[Image:Constraint_Horizontal.svg|32px]] [[Sketcher_ConstrainHorizontal|Horizontal]]: Constrains the selected lines or polyline elements to a true horizontal orientation. More than one object can be selected before applying this constraint. | ||
+ | |||
+ | * [[Image:Constraint_Parallel.svg|32px]] [[Sketcher_ConstrainParallel|Parallel]]: Constrains two or more lines parallel to one another. | ||
+ | |||
+ | * [[Image:Constraint_Perpendicular.svg|32px]] [[Sketcher_ConstrainPerpendicular|Perpendicular]]: Constrains two lines perpendicular to one another, or constrains a line perpendicular to an arc endpoint. | ||
+ | |||
+ | * [[Image:Constraint_Tangent.svg|32px]] [[Sketcher ConstrainTangent|Tangent]]: Creates a tangent constraint between two selected entities, or a co-linear constraint between two line segments. A line segment does not have to lie directly on an arc or circle to be constrained tangent to that arc or circle. | ||
+ | |||
+ | * [[Image:Constraint_EqualLength.svg|32px]] [[Sketcher_ConstrainEqual|Equal Length]]: Constrains two selected entities equal to one another. If used on circles or arcs their radii will be set equal. | ||
+ | |||
+ | * [[Image:Constraint_Symmetric.svg|32px]] [[Sketcher_ConstrainSymmetric|Symmetric]]: Constrains two points symmetrically about a line, or constrains the first two selected points symmetrically about a third selected point. | ||
+ | |||
+ | * [[Image:Sketcher_ConstrainBlock.svg|32px]] [[Sketcher_ConstrainBlock|Constrain Block]]: Basically allows to block a geometric element in place with a single constraint. It should be particularly useful to work with B-Splines. See the [https://forum.freecadweb.org/viewtopic.php?f=9&t=26572 Block Constraint forum topic]. {{Version|0.17}} | ||
+ | |||
+ | ====Dimensional constraints ==== | ||
+ | These are constraints associated with numeric data, for which you can use the [[Expressions|expressions]]. The data may be taken from a [[Spreadsheet_Workbench|spreadsheet]]. | ||
+ | |||
+ | * [[Image:Sketcher_ConstrainLock.svg|32px]] [[Sketcher ConstrainLock|Lock]]: Constrains the selected item by setting vertical and horizontal distances relative to the origin, thereby locking the location of that item. These constraint distances can be edited later. | ||
+ | |||
+ | * [[Image:Constraint_HorizontalDistance.svg|32px]] [[Sketcher ConstrainDistanceX|Horizontal Distance]]: Fixes the horizontal distance between two points or line endpoints. If only one item is selected, the distance is set to the origin. | ||
+ | |||
+ | * [[Image:Constraint_VerticalDistance.svg|32px]] [[Sketcher_ConstrainDistanceY|Vertical Distance]]: Fixes the vertical distance between 2 points or line endpoints. If only one item is selected, the distance is set to the origin. | ||
+ | |||
+ | * [[Image:Constraint_Length.svg|32px]] [[Sketcher_ConstrainDistance|Distance]]: Defines the distance of a selected line by constraining its length, or defines the distance between two points by constraining the distance between them. | ||
+ | |||
+ | * [[Image:Constraint_Radius.svg|32px]] [[Sketcher_ConstrainRadius|Radius]]: Defines the radius of a selected arc or circle by constraining the radius. | ||
+ | * [[Image:Constraint_InternalAngle.png|32px]] [[Sketcher_ConstrainAngle|Internal Angle]]: Defines the internal angle between two selected lines. | ||
+ | |||
+ | * [[Image:Constraint_SnellsLaw.svg|32px]] [[Sketcher ConstrainSnellsLaw|Snell's Law]]: Constrains two lines to obey a refraction law to simulate the light going through an interface. {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Constraint_InternalAlignment.svg|32px]] [[Sketcher_ConstrainInternalAlignment|Internal Alignment]]: Aligns selected elements to selected shape (e.g. a line to become major axis of an ellipse). | ||
+ | |||
+ | * [[Image:Sketcher_ToggleConstraint.svg|32px]] [[Sketcher_ToggleDrivingConstraint|Toggle reference/driving constraint]]: Toggles the toolbar or the selected constraints to/from reference mode. {{Version|0.16}} | ||
+ | |||
+ | ===Sketcher tools=== | ||
+ | |||
+ | * [[File:Sketcher SelectElementsWithDoFs.svg|32px]] [[Sketcher_SelectElementsWithDoFs|Select solver DOFs]]: Highlights in green the geometry with degrees of freedom (DOFs), i.e. not fully constrained. {{Version|0.18}} | ||
+ | |||
+ | * [[Image:Sketcher CloseShape.svg|32px]] [[Sketcher CloseShape|Close Shape]]: Creates a closed shape by applying coincident constraints to endpoints {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Sketcher ConnectLines.svg|32px]] [[Sketcher ConnectLines|Connect Edges]]: Connect sketcher elements by applying coincident constraints to endpoints {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Sketcher SelectConstraints.svg|32px]] [[Sketcher SelectConstraints|Select Constraints]]: Selects the constraints of a sketcher element {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Sketcher SelectOrigin.svg|32px]] [[Sketcher SelectOrigin|Select Origin]]: Selects the origin of a sketch {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Sketcher SelectVerticalAxis.svg|32px]] [[Sketcher SelectVerticalAxis|Select Vertical Axis]]: Selects the vertical axis of a sketch {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Sketcher SelectHorizontalAxis.svg|32px]] [[Sketcher SelectHorizontalAxis|Select Horizontal Axis]]: Selects the horizontal axis of a sketch {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Sketcher SelectRedundantConstraints.svg|32px]] [[Sketcher SelectRedundantConstraints|Select Redundant Constraints]]: Selects redundant constraints of a sketch {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Sketcher SelectConflictingConstraints.svg|32px]] [[Sketcher SelectConflictingConstraints|Select Conflicting Constraints]]: Selects conflicting constraints of a sketch {{Version|0.15}} | ||
+ | |||
+ | * [[Image:Sketcher SelectElementsAssociatedWithConstraints.svg|32px]] [[Sketcher SelectElementsAssociatedWithConstraints|Select Elements Associated with constraints]]: Select sketcher elements associated with constraints {{Version|0.15}} | ||
+ | |||
+ | * [[File:Sketcher_Element_Ellipse_All.svg|32px]] [[Sketcher_RestoreInternalAlignmentGeometry|Show/Hide internal geometry]]: Recreates missing/deletes unneeded internal geometry of a selected ellipse, arc of ellipse/hyperbola/parabola or B-spline. | ||
+ | |||
+ | * [[Image:Sketcher Symmetry.svg|32px]] [[Sketcher Symmetry|Symmetry]]: Copies a sketcher element symmetrical to a chosen line {{Version|0.16}} | ||
+ | |||
+ | * [[Image:Sketcher Clone.svg|32px]] [[Sketcher Clone|Clone]]: Clones a sketcher element {{Version|0.16}} | ||
+ | |||
+ | * [[Image:Sketcher Copy.svg|32px]] [[Sketcher Copy|Copy]]: Copies a sketcher element {{Version|0.16}} | ||
+ | |||
+ | * [[File:Sketcher_Move.svg|32px]] [[Sketcher_Move|Move]]: Moves the selected geometry taking as reference the last selected point. {{Version|0.18}} | ||
+ | |||
+ | * [[Image:Sketcher RectangularArray.svg|32px]] [[Sketcher RectangularArray|Rectangular Array]]: Creates an array of selected sketcher elements {{Version|0.16}} | ||
+ | |||
+ | * [[File:Sketcher Element SelectionTypeInvalid.svg|32px]] [[Sketcher_DeleteAllGeometry|Delete All Geometry]]: Deletes all geometry from the sketch. {{Version|0.18}} | ||
+ | |||
+ | * [[File:Sketcher Element SelectionTypeInvalid.svg|32px]] [[Sketcher_DeleteAllConstraints|Delete All Constraints]]: Deletes all constraints from the sketch. {{Version|0.18}} | ||
+ | |||
+ | ===Sketcher B-spline tools=== | ||
+ | |||
+ | * [[File:Sketcher_BSplineDegree.svg|32px]] [[Sketcher_BSplineDegree|Show/Hide B-spline degree]] | ||
+ | |||
+ | * [[File:Sketcher_BSplinePolygon.svg|32px]] [[Sketcher_BSplinePolygon|Show/Hide B-spline control polygon]] | ||
+ | |||
+ | * [[File:Sketcher_BSplineComb.svg|32px]] [[Sketcher_BSplineComb|Show/Hide B-spline curvature comb]] | ||
+ | |||
+ | * [[File:Sketcher_BSplineKnotMultiplicity.svg|32px]] [[Sketcher_BSplineKnotMultiplicity|Show/Hide B-spline knot multiplicity]] | ||
+ | |||
+ | * [[File:Sketcher_BSplineApproximate.svg|32px]] [[Sketcher_ConvertToNURB|Convert Geometry to B-spline]] | ||
+ | |||
+ | * [[File:Sketcher_BSplineIncreaseDegree.svg|32px]] [[Sketcher_BSplineIncreaseDegree|Increase degree]] | ||
+ | |||
+ | * [[File:Sketcher_BSplineIncreaseKnotMultiplicity.svg|32px]] [[Sketcher_BSplineIncreaseKnotMultiplicity|Increase knot multiplicity]] | ||
+ | |||
+ | * [[File:Sketcher_BSplineDecreaseKnotMultiplicity.svg|32px]] [[Sketcher_BSplineDecreaseKnotMultiplicity|Decrease knot multiplicity]] | ||
+ | |||
+ | ===Sketcher virtual space=== | ||
+ | |||
+ | * [[Image:Sketcher SwitchVirtualSpace.svg|32px]] [[Sketcher_SwitchVirtualSpace|Switch Virtual Space]]: Allows you to hide all constraints of a sketch and make them visible again. {{Version|0.17}} | ||
+ | |||
+ | ===Preferences=== | ||
+ | |||
+ | * [[Image:Preferences-general.svg|32px]] [[Sketcher_Preferences|Preferences]]: Preferences for the '''Sketcher''' workbench. | ||
+ | |||
+ | == Best Practices == | ||
Every CAD user develops his own way of working over time, but there are some useful general principles to follow. | Every CAD user develops his own way of working over time, but there are some useful general principles to follow. | ||
Line 53: | Line 263: | ||
* If you have the possibility to choose between the Length constraint and the Horizontal or Vertical Distance constraints, prefer the latter. Horizontal and Vertical Distance constraints are computationally cheaper. | * If you have the possibility to choose between the Length constraint and the Horizontal or Vertical Distance constraints, prefer the latter. Horizontal and Vertical Distance constraints are computationally cheaper. | ||
* In general, the best constraints to use are: Horizontal and Vertical Constraints; Horizontal and Vertical Length Constraints; Point-to-Point Tangency. If possible, limit the use of these: the general Length Constraint; Edge-to-Edge Tangency; Fix Point Onto a Line Constraint; Symmetry Constraint. | * In general, the best constraints to use are: Horizontal and Vertical Constraints; Horizontal and Vertical Length Constraints; Point-to-Point Tangency. If possible, limit the use of these: the general Length Constraint; Edge-to-Edge Tangency; Fix Point Onto a Line Constraint; Symmetry Constraint. | ||
+ | * If in doubt about the validity of a sketch once it is complete (features turn green), close the Sketcher dialog, switch to the [[Part Workbench|Part Workbench]] and run [[Part CheckGeometry|Check geometry]]. | ||
+ | == Tutorials == | ||
− | == | + | * [https://forum.freecadweb.org/viewtopic.php?f=36&t=30104 Sketcher tutorial] by chrisb. This is a 70-page long PDF document that serves as a detailed manual for the sketcher. It explains the basics of Sketcher usage, and goes into a lot of detail about the creation of geometrical shapes, and each of the constraints. |
− | + | * [[Sketcher tutorial|Sketcher tutorial]] for beginners | |
− | * [[ | + | * [[Sketcher Micro Tutorial - Constraint Practices|Sketcher Micro Tutorial - Constraint Practices]] |
− | * [[ | + | * [[Sketcher requirement for a sketch|Sketcher requirement for a sketch]] Minimum requirement for a sketch and Complete determination of a sketch |
− | [[Category:User Documentation]] | + | <div class="mw-translate-fuzzy"> |
+ | [[Category:User Documentation/zh-tw]] | ||
+ | </div> | ||
− | + | {{Sketcher Tools navi}} | |
+ | {{Userdocnavi}} | ||
+ | [[Category:Workbenches]] |
Latest revision as of 12:43, 6 November 2019
Introduction
速寫坊 是用於創建平面幾何給 零件坊 以及其他工作坊。一般而言平面幾何被視為大部分 CAD 模型起點。簡易平面草稿0可以"擠出"為立體形狀，進一步平面草稿可在立體表面開口，且草稿可在立體物表面定義'路徑 （擠出）'。搭配 布林運算 草稿形塑原創 solid shape 設計核心。
The Sketcher workbench features "constraints", allowing 2D shapes to follow precise geometrical definitions in terms of length, angles, and relationships (horizontality, verticality, perpendicularity, etc.). A constraint solver calculates the constrained-extent of 2D geometry and allows interactive exploration of degrees-of-freedom of the sketch.
A fully constrained sketch
Basics of constraint sketching
To explain how the Sketcher works, it may be useful to compare it to the "traditional" way of drafting.
Traditional Drafting
The traditional way of CAD drafting inherits from the old drawing board. Orthogonal (2D) views are drawn manually and intended for producing technical drawings (also known as blueprints). Objects are drawn precisely to the intended size or dimension. If you want to draw an horizontal line 100mm in length starting at (0,0), you activate the line tool, either click on the screen or input the (0,0) coordinates for the first point, then make a second click or input the second point coordinates at (100,0). Or you will draw your line without regard to its position, and move it afterwards. When you've finished drawing your geometries, you add dimensions to them.
Constraint Sketching
The Sketcher moves away from this logic. Objects do not need to be drawn exactly as you intend to, because they will be defined later on by constraints. Objects can be drawn loosely, and as long as they are unconstrained, can be modified. They are in effect "floating" and can be moved, stretched, rotated, scaled, and so on. This gives great flexibility in the design process.
What are constraints?
Instead of dimensions, Constraints are used to limit the degrees of freedom of an object. For example, a line without constraints has 4 Degrees Of Freedom (abbreviated as " DOF "): it can be moved horizontally or vertically, it can be stretched, and it can be rotated.
Applying a horizontal or vertical constraint, or an angle constraint (relative to another line or to one of the axes), will limit its capacity to rotate, thus leaving it with 3 degrees of freedom. Locking one of its points in relation to the origin will remove another 2 degrees of freedom. And applying a dimension constraint will remove the last degree of freedom. The line is then considered fully-constrained.
Multiple objects can be constrained between one another. Two lines can be joined through one of their points with the coincident point constraint. An angle can be set between them, or they can be set perpendicular. A line can be tangent to an arc or a circle, and so on. A complex Sketch with multiple objects will have a number of different solutions, and making it fully-constrained means that just one of these possible solutions has been reached based on the applied constraints.
There are two kinds of constraints: geometric and dimensional. They are detailed in the 'The tools' section below.
What the Sketcher is not good for
The Sketcher is not intended for producing 2D blueprints. Once sketches are used to generate a solid feature, they are automatically hidden. Constraints are only visible in Sketch edit mode.
If you only need to produce 2D views for print, and don't want to create 3D models, check out the Draft workbench. Unlike Sketcher elements, Draft objects don't use constraints; they are simple shapes defined at the moment of creation. Both Draft and Sketcher can be used for 2D geometry drawing, and 3D solid creation, although their preferred use is different; the Sketcher is normally used together with Part and PartDesign to create solids; Draft is normally used for simple planar drawings over a grid, as when drawing an architectural floor plan; in these situations Draft is mostly used together with the Arch Workbench. The tool Draft2Sketch converts a Draft object to a Sketch object, and vice versa; many tools that require a 2D element as input work with either type of object as an internal conversion is done automatically.
Sketching Workflow
A Sketch is always 2-dimensional (2D). To create a solid, a 2D Sketch of a single enclosed area is created and then either Padded or Revolved to add the 3rd dimension, creating a 3D solid from the 2D Sketch.
If a Sketch has segments that cross one another, places where a Point is not directly on a segment, or places where there are gaps between endpoints of adjacent segments, Pad or Revolve won't create a solid. Sometimes a Sketch which contains lines which cross one another will work for a simple operation such as Pad, but later operations such as Linear Pattern will fail. It is best to avoid crossing lines. The exception to this rule is that it doesn't apply to Construction (blue) Geometry.
Inside the enclosed area we can have smaller non-overlapping areas. These will become voids when the 3D solid is created.
Once a Sketch is fully constrained, the Sketch features will turn green; Construction Geometry will remain blue. It is usually "finished" at this point and suitable for use in creating a 3D solid. However, once the Sketch dialog is closed it may be worthwhile going to Part Workbench and running Check geometry to ensure there are no features in the Sketch which may cause later problems.
The tools
The Sketcher Workbench tools are all located in the Sketch menu that appears when you load the Sketcher Workbench.
- New sketch: Creates a new sketch on a selected face or plane. If no face is selected while this tool is executed the user is prompted to select a plane from a pop-up window.
- Edit sketch: Edit the selected Sketch. This will open the Sketcher Dialog.
- Leave sketch: Leave the Sketch editing mode.
- View sketch: Sets the model view perpendicular to the sketch plane.
- View section: Creates a section plane that temporarily hides any matter in front of the sketch plane. introduced in version 0.18
- Map sketch to face: Maps a sketch to the previously selected face of a solid.
- Reorient sketch : Allows you to change the position of a sketch
- Validate sketch: Verify the tolerance of different points and adjust them.
- Merge sketches: Merge two or more sketches. introduced in version 0.15
- Mirror sketch: Mirror a sketch along the x-axis, the y-axis or the origin. introduced in version 0.16
Sketcher geometries
These are tools for creating objects.
- Point: Draws a point.
- Line: Draws a line segment between 2 points. Lines are infinite regarding certain constraints.
- Create an arc: This is an icon menu in the Sketcher toolbar that holds the following commands:
- Arc: Draws an arc segment from center, radius, start angle and end angle.
- Arc by 3 points: Draws an arc segment from two endpoints and another point on the circumference.
- Create a circle: This is an icon menu in the Sketcher toolbar that holds the following commands:
- Circle: Draws a circle from center and radius.
- Circle by 3 points: Draws a circle from three points on the circumference.
- Create a conic: The sketcher provides the following conical sections. Unlike B-splines they can be used with all sorts of constraints such as tangents, point-on-object, or orthogonal.
- Ellipse by center: Draws an ellipse by center point, major radius point and minor radius point. introduced in version 0.15
- Ellipse by 3 points: Draws an ellipse by major diameter (2 points) and minor radius point. introduced in version 0.15
- Arc of ellipse: Draws an arc of ellipse by center point, major radius point, starting point and ending point. introduced in version 0.15
- Arc of hyperbola: Draws an arc of hyperbola. introduced in version 0.17
- Arc of parabola: Draws an arc of parabola. introduced in version 0.17
- Create a B-spline: This is an icon menu in the Sketcher toolbar that holds the following commands:
- Create B-spline: Draws a B-spline curve by its control points. introduced in version 0.17
- Create periodic B-spline: Draws a periodic (closed) B-spline curve by its control points. introduced in version 0.17
- Polyline (multiple-point line): Draws a line made of multiple line segments. Pressing the M key while drawing a Polyline toggles between the different polyline modes.
- Rectangle: Draws a rectangle from 2 opposite points.
- Create regular polygon: This is an icon menu in the Sketcher toolbar that holds the following commands:
- Triangle: Draws a regular triangle inscribed in a construction geometry circle. introduced in version 0.15
- Square: Draws a regular square inscribed in a construction geometry circle. introduced in version 0.15
- Pentagon: Draws a regular pentagon inscribed in a construction geometry circle. introduced in version 0.15
- Hexagon: Draws a regular hexagon inscribed in a construction geometry circle. introduced in version 0.15
- Heptagon: Draws a regular heptagon inscribed in a construction geometry circle. introduced in version 0.15
- Octagon: Draws a regular octagon inscribed in a construction geometry circle. introduced in version 0.15
- Create Regular Polygon : Draws a regular polygon by selecting the number of sides and picking two points: the center and one corner.
- Slot: Draws an oval by selecting the center of one semicircle and an endpoint of the other semicircle.
- Fillet: Makes a fillet between two lines joined at one point. Select both lines or click on the corner point, then activate the tool.
- Trimming: Trims a line, circle or arc with respect to the clicked point.
- Extend: Extends a line or an arc to a boundary line, arc, ellipse, arc of ellipse or a point in space. introduced in version 0.17
- External Geometry: Creates an edge linked to external geometry.
- CarbonCopy: Copies the geometry of another sketch. introduced in version 0.17
- Construction Mode: Toggles sketch geometry from/to construction mode. Construction geometry is shown in blue and is discarded outside of Sketch editing mode.
Sketcher constraints
Constraints are used to define lengths, set rules between sketch elements, and to lock the sketch along the vertical and horizontal axes. Some constraints require use of Helper constraints.
Geometric constraints
These constraints are not associated with numeric data.
- Coincident: Affixes a point onto (coincident with) one or more other points.
- Point On Object: Affixes a point onto another object such as a line, arc, or axis.
- Vertical: Constrains the selected lines or polyline elements to a true vertical orientation. More than one object can be selected before applying this constraint.
- Horizontal: Constrains the selected lines or polyline elements to a true horizontal orientation. More than one object can be selected before applying this constraint.
- Parallel: Constrains two or more lines parallel to one another.
- Perpendicular: Constrains two lines perpendicular to one another, or constrains a line perpendicular to an arc endpoint.
- Tangent: Creates a tangent constraint between two selected entities, or a co-linear constraint between two line segments. A line segment does not have to lie directly on an arc or circle to be constrained tangent to that arc or circle.
- Equal Length: Constrains two selected entities equal to one another. If used on circles or arcs their radii will be set equal.
- Symmetric: Constrains two points symmetrically about a line, or constrains the first two selected points symmetrically about a third selected point.
- Constrain Block: Basically allows to block a geometric element in place with a single constraint. It should be particularly useful to work with B-Splines. See the Block Constraint forum topic. introduced in version 0.17
Dimensional constraints
These are constraints associated with numeric data, for which you can use the expressions. The data may be taken from a spreadsheet.
- Lock: Constrains the selected item by setting vertical and horizontal distances relative to the origin, thereby locking the location of that item. These constraint distances can be edited later.
- Horizontal Distance: Fixes the horizontal distance between two points or line endpoints. If only one item is selected, the distance is set to the origin.
- Vertical Distance: Fixes the vertical distance between 2 points or line endpoints. If only one item is selected, the distance is set to the origin.
- Distance: Defines the distance of a selected line by constraining its length, or defines the distance between two points by constraining the distance between them.
- Radius: Defines the radius of a selected arc or circle by constraining the radius.
- Internal Angle: Defines the internal angle between two selected lines.
- Snell's Law: Constrains two lines to obey a refraction law to simulate the light going through an interface. introduced in version 0.15
- Internal Alignment: Aligns selected elements to selected shape (e.g. a line to become major axis of an ellipse).
- Toggle reference/driving constraint: Toggles the toolbar or the selected constraints to/from reference mode. introduced in version 0.16
Sketcher tools
- Select solver DOFs: Highlights in green the geometry with degrees of freedom (DOFs), i.e. not fully constrained. introduced in version 0.18
- Close Shape: Creates a closed shape by applying coincident constraints to endpoints introduced in version 0.15
- Connect Edges: Connect sketcher elements by applying coincident constraints to endpoints introduced in version 0.15
- Select Constraints: Selects the constraints of a sketcher element introduced in version 0.15
- Select Origin: Selects the origin of a sketch introduced in version 0.15
- Select Vertical Axis: Selects the vertical axis of a sketch introduced in version 0.15
- Select Horizontal Axis: Selects the horizontal axis of a sketch introduced in version 0.15
- Select Redundant Constraints: Selects redundant constraints of a sketch introduced in version 0.15
- Select Conflicting Constraints: Selects conflicting constraints of a sketch introduced in version 0.15
- Select Elements Associated with constraints: Select sketcher elements associated with constraints introduced in version 0.15
- Show/Hide internal geometry: Recreates missing/deletes unneeded internal geometry of a selected ellipse, arc of ellipse/hyperbola/parabola or B-spline.
- Symmetry: Copies a sketcher element symmetrical to a chosen line introduced in version 0.16
- Clone: Clones a sketcher element introduced in version 0.16
- Copy: Copies a sketcher element introduced in version 0.16
- Move: Moves the selected geometry taking as reference the last selected point. introduced in version 0.18
- Rectangular Array: Creates an array of selected sketcher elements introduced in version 0.16
- Delete All Geometry: Deletes all geometry from the sketch. introduced in version 0.18
- Delete All Constraints: Deletes all constraints from the sketch. introduced in version 0.18
Sketcher B-spline tools
Sketcher virtual space
- Switch Virtual Space: Allows you to hide all constraints of a sketch and make them visible again. introduced in version 0.17
Preferences
- Preferences: Preferences for the Sketcher workbench.
Best Practices
Every CAD user develops his own way of working over time, but there are some useful general principles to follow.
- A series of simple sketches is easier to manage than a single complex one. For example, a first sketch can be created for the base 3D feature (either a pad or a revolve), while a second one can contain holes or cutouts (pockets). Some details can be left out, to be realized later on as 3D features. You can choose to avoid fillets in your sketch if there are too many, and add them as a 3D feature.
- Always create a closed profile, or your sketch won't produce a solid, but rather a set of open faces. If you don't want some of the objects to be included in the solid creation, turn them to construction elements with the Construction Mode tool.
- Use the auto constraints feature to limit the number of constraints you'll have to add manually.
- As a general rule, apply geometric constraints first, then dimensional constraints, and lock your sketch last. But remember: rules are made to be broken. If you're having trouble manipulating your sketch, it may be useful to constrain a few objects first before completing your profile.
- If possible, center your sketch to the origin (0,0) with the lock constraint. If your sketch is not symmetric, locate one of its points to the origin, or choose nice round numbers for the lock distances. In v0.12, external constraints (constraining the sketch to existing 3D geometry like edges or to other sketches) are not implemented. This means that to locate following sketches geometry to your first sketch, you'll need to set distances relative to your first sketch manually. A lock constraint of (25,75) from the origin is more easily remembered than (23.47,73.02).
- If you have the possibility to choose between the Length constraint and the Horizontal or Vertical Distance constraints, prefer the latter. Horizontal and Vertical Distance constraints are computationally cheaper.
- In general, the best constraints to use are: Horizontal and Vertical Constraints; Horizontal and Vertical Length Constraints; Point-to-Point Tangency. If possible, limit the use of these: the general Length Constraint; Edge-to-Edge Tangency; Fix Point Onto a Line Constraint; Symmetry Constraint.
- If in doubt about the validity of a sketch once it is complete (features turn green), close the Sketcher dialog, switch to the Part Workbench and run Check geometry.
Tutorials
- Sketcher tutorial by chrisb. This is a 70-page long PDF document that serves as a detailed manual for the sketcher. It explains the basics of Sketcher usage, and goes into a lot of detail about the creation of geometrical shapes, and each of the constraints.
- Sketcher tutorial for beginners
- Sketcher Micro Tutorial - Constraint Practices
- Sketcher requirement for a sketch Minimum requirement for a sketch and Complete determination of a sketch
- The tools: New sketch, Edit sketch, Leave sketch, View sketch, View section, Map sketch to face, Reorient sketch, Validate sketch, Merge sketches, Mirror sketch
- Sketcher geometries: Point, Line by 2 point, Create an arc, Arc, Arc by 3 Point, Create a circle, Circle, Circle by 3 Point, Create a conic, Ellipse by center, Ellipse by 3 points, Arc of ellipse, Arc of hyperbola, Arc of parabola, Create a B-spline, Create B-spline, Create periodic B-pline, Polyline (multiple-point line), Rectangle, Create regular polygon, Triangle, Square, Pentagon, Hexagon, Heptagon, Octagon, Create Regular Polygon, Slot, Fillet, Trimming, Extend, External Geometry, CarbonCopy, Construction Mode
- Sketcher constraints
- Geometric constraints Coincident, Point On Object, Vertical, Horizontal, Parallel, Perpendicular, Tangent, Equal Length, Symmetric, Constrain Block
- Dimensional constraints Lock, Horizontal Distance, Vertical Distance, Distance, Radius, Internal Angle, Snell's Law, Internal Alignment, Toggle reference/driving constraint,
- Sketcher tools Select solver DOFs, Close Shape, Connect Edges, Select Constraints, Select Origin, Select Vertical Axis, Select Horizontal Axis, Select Redundant Constraints, Select Conflicting Constraints, Select Elements Associated with constraints, Show/Hide internal geometry, Symmetry, Clone, Copy, Move, Rectangular Array, Delete All Geometry, Delete All Constraints
- Sketcher B-spline tools Show/Hide B-spline degree, Show/Hide B-spline control polygon, Show/Hide B-spline curvature comb, Show/Hide B-spline knot multiplicity, Convert Geometry to B-spline, Increase degree, Increase knot multiplicity, Decrease knot multiplicity
- Sketcher virtual space Switch Virtual Space
- Installation: Unix, Windows, Mac; Getting started
- Basics: About FreeCAD, Workbenches, Preferences, Document structure, Interface Customization, Properties, Mouse Model; Tutorials
- Workbenches: Std Base; Arch, Draft, FEM, Image, Inspection, Mesh, OpenSCAD, Part, PartDesign, Path, Plot, Points, Raytracing, Reverse Engineering, Robot, Ship, Sketcher, Spreadsheet, Start, Surface workbench, TechDraw, Test Framework, Web
- Scripting: Introduction to Python, FreeCAD scripting tutorial, FreeCAD Scripting Basics, How to install macros, Gui Command, Units Modules: Builtin modules, Workbench creation, Installing more workbenches Meshes: Mesh Scripting, Mesh Module Parts: The Part Module, Topological data scripting, PythonOCC, Mesh to Part Coin scenegraph: The Coin/Inventor scenegraph, Pivy Qt interface: PySide, Using the FreeCAD GUI, Dialog creation Parametric objects: Scripted objects Other: Code snippets, Line drawing function, Embedding FreeCAD, FreeCAD vector math library, Power users hub, Python, Macros, FreeCAD Scripting Basics, Topological data scripting