Sketcher Создать эллипс от центра
Sketcher Эллипс по центральной точке |
Системное название |
---|
Sketcher Create Ellipse by center |
Расположение в меню |
Эскиз → Геометрия эскиза → Эллипс по центральной точке |
Верстаки |
Sketcher |
Быстрые клавиши |
Нет |
Представлено в версии |
0.15 |
См. также |
Sketcher Эллипс по 3 точкам, Sketcher Круг, Sketcher Дуга по эллипсу |
Описание
Этот инструмент рисует эллипс, указывая три точки: центральную, конец большого радиуса, малый радиус. При запуске инструмента указатель мыши меняется на белый крест с красным значком эллипса. Кроме того, координаты отображаются в режиме реального времени.
Как использовать
- Вызовите команду, нажав кнопку на панели инструментов, выбрав пункт меню или используя сочетание клавиш (сперва вы должны назначить их в Настройках интерфейса).
- Сначала в 3D-виде нажатием задайте центр эллипса. Вторым нажатием задайте первый радиус и ориентацию эллипса. Третьим нажатием задайте другой радиус (расстояние от линии, определенной первыми двумя нажатиями, является вторым радиусом).
- После третьего нажатия создается эллипс вместе с набором вспомогательной геометрии, привязанной к нему (большой диаметр, малый диаметр, два фокуса). Вспомогательная геометрия может быть удалена вручную, если не нужна, и воссоздана позже. Смотрите Выравнивание Внутренних Ограничений и Sketcher Показать Скрытую Внутреннюю Геометрию.
- Нажмите ESC или правую кнопку мыши для отмены функции.
Peculiarities
- Major and minor axes of ellipses are strict and cannot be swapped by resizing the ellipse. This is a consequence of the solver parametrization used (center (x,y), focus1 (x,y) and minor radius length (b)) and the same strict behavior of OpenCascade. The ellipse must be rotated to swap the axes.
- Ellipse can function as a circle when its major and minor diameter lines are deleted, and one of the foci is constrained to coincide with the center. But radius constraint won't work on such a circle.
- Moving the ellipse by edge is the same as moving ellipse's center.
Sketcher
- General: Create sketch, Edit sketch, Map sketch to face, Reorient sketch, Validate sketch, Merge sketches, Mirror sketch, Leave sketch, View sketch, View section, Toggle grid, Toggle snap, Configure rendering order, Stop operation
- Sketcher geometries: Point, Line, Arc, Arc by 3 points, Circle, Circle by 3 points, Ellipse, Ellipse by 3 points, Arc of ellipse, Arc of hyperbola, Arc of parabola, B-spline by control points, Periodic B-spline by control points, B-spline by knots, Periodic B-spline by knots, Polyline, Rectangle, Centered rectangle, Rounded rectangle, Triangle, Square, Pentagon, Hexagon, Heptagon, Octagon, Regular polygon, Slot, Fillet, Corner-preserving fillet, Trim, Extend, Split, External geometry, Carbon copy, Toggle construction geometry
- Sketcher constraints:
- Geometric constraints: Coincident, Point on object, Vertical, Horizontal, Parallel, Perpendicular, Tangent, Equal, Symmetric, Block
- Dimensional constraints: Lock, Horizontal distance, Vertical distance, Distance, Radius or weight, Diameter, Auto radius/diameter, Angle, Refraction (Snell's law)
- Constraint tools: Toggle driving/reference constraint, Activate/deactivate constraint
- Sketcher tools: Select unconstrained DoF, Select associated constraints, Select associated geometry, Select redundant constraints, Select conflicting constraints, Show/hide internal geometry, Select origin, Select horizontal axis, Select vertical axis, Symmetry, Clone, Copy, Move, Rectangular array, Remove axes alignment, Delete all geometry, Delete all constraints
- Sketcher B-spline tools: Show/hide B-spline degree, Show/hide B-spline control polygon, Show/hide B-spline curvature comb, Show/hide B-spline knot multiplicity, Show/hide B-spline control point weight, Convert geometry to B-spline, Increase B-spline degree, Decrease B-spline degree, Increase knot multiplicity, Decrease knot multiplicity, Insert knot, Join curves
- Sketcher virtual space: Switch virtual space
- Additional: Sketcher Dialog, Preferences, Sketcher scripting
User documentation
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web
- Hubs: User hub, Power users hub, Developer hub