Part Sphere/cs: Difference between revisions
(Created page with "Díl Koule") |
(Updating to match new version of source page) |
||
(15 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
⚫ | |||
⚫ | |||
{{Docnav|[[Part_Cylinder|Cylinder]]|[[Part_Torus|Torus]]|[[Part_Module|Part]]|IconL=Part_Cylinder.png|IconC=Workbench_Part.svg|IconR=Part_Torus.png}} |
|||
<div class="mw-translate-fuzzy"> |
|||
Creates a simple parametric sphere, with position, angle1, angle2, angle3 and radius parameters. The sphere will be positioned at origin (point 0,0,0) on creation. The angle parameters permit to make a portion of sphere instead of a full sphere (they are set to 360° by default) |
|||
⚫ | |||
</div> |
|||
Vytvoří jednoduchou parametrickou kouli podle parametrů pozice, úhel1, úhel2, úhel3 a poloměr. |
|||
[[File:SimpleSphere.jpg|400px]] |
|||
<div class="mw-translate-fuzzy"> |
|||
== Použití == |
|||
V pracovní ploše [[Part_Workbench/cs|Díl]] klikněte na ikonu koule [[Image:Part Sphere.png|32px]]. |
|||
Koule bude při vytvoření umístěna do počátečního bodu (bod 0,0,0). Parametry úhly dovolují vytvořit částečnou kouli místo celé koule (defaultně jsou nastaveny na 360°) |
|||
</div> |
|||
== Volby == |
|||
The parametric sphere is defined by the following parameters: |
|||
* Radius |
|||
* Angle 1 |
|||
* Angle 2 |
|||
* Angle 3 |
|||
* as well as the standard set of placement parameters |
|||
The picture below gives an overview of a parametric sphere with parameters different from the default value. |
|||
[[File:PartDesign_Sphere_Parameter_en.jpg|600px]] |
|||
====Parameter==== |
|||
* {{Parameter|Radius:}} Radius of the sphere |
|||
* {{Parameter|Angle 1:}} 1nd angle to cut / define the sphere |
|||
* {{Parameter|Angle 2:}} 2nd angle to cut / define the sphere |
|||
* {{Parameter|Angle 3:}} 3rd angle to cut / define the sphere |
|||
Because it is quite difficult to explain the meaning of the parameters angle 1, angle 2, angle 3, the picture below gives an explanation about these parameters with following values: angle 1 = -45°, angle 2 = 45° and angle 3= 90°. |
|||
[[File:SphereCutThreeAngles.jpg|400px]] |
|||
{{clear}} |
{{clear}} |
||
⚫ | |||
{{Docnav|[[Part_Cylinder|Cylinder]]|[[Part_Torus|Torus]]|[[Part_Module|Part]]|IconL=Part_Cylinder.png|IconC=Workbench_Part.svg|IconR=Part_Torus.png}} |
|||
{{Part Tools navi}} |
|||
{{Userdocnavi}} |
Revision as of 14:17, 13 February 2019
Díl Koule |
Umístění Menu |
---|
Díl -> Koule |
Pracovní stoly |
Modul Díl, Kompletace |
Výchozí zástupce |
Nikdo |
Představen ve verzi |
- |
Viz také |
Díl Vytváření zákl.geom.tvarů |
Vytvoří jednoduchou parametrickou kouli podle parametrů pozice, úhel1, úhel2, úhel3 a poloměr.
Použití
V pracovní ploše Díl klikněte na ikonu koule . Koule bude při vytvoření umístěna do počátečního bodu (bod 0,0,0). Parametry úhly dovolují vytvořit částečnou kouli místo celé koule (defaultně jsou nastaveny na 360°)
Volby
The parametric sphere is defined by the following parameters:
- Radius
- Angle 1
- Angle 2
- Angle 3
- as well as the standard set of placement parameters
The picture below gives an overview of a parametric sphere with parameters different from the default value.
Parameter
- Radius: Radius of the sphere
- Angle 1: 1nd angle to cut / define the sphere
- Angle 2: 2nd angle to cut / define the sphere
- Angle 3: 3rd angle to cut / define the sphere
Because it is quite difficult to explain the meaning of the parameters angle 1, angle 2, angle 3, the picture below gives an explanation about these parameters with following values: angle 1 = -45°, angle 2 = 45° and angle 3= 90°.
Part
- Primitives: Box, Cylinder, Sphere, Cone, Torus, Tube, Create primitives, Shape builder
- Creation and modification: Extrude, Revolve, Mirror, Fillet, Chamfer, Make face from wires, Ruled Surface, Loft, Sweep, Section, Cross sections, 3D Offset, 2D Offset, Thickness, Projection on surface, Attachment
- Boolean: Make compound, Explode Compound, Compound Filter, Boolean, Cut, Fuse, Common, Connect, Embed, Cutout, Boolean fragments, Slice apart, Slice, XOR
- Measure: Measure Linear, Measure Angular, Measure Refresh, Clear All, Toggle All, Toggle 3D, Toggle Delta
User documentation
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web
- Hubs: User hub, Power users hub, Developer hub