Part Sphere/cs: Difference between revisions
(Updating to match new version of source page) |
(Updating to match new version of source page) |
||
(6 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
⚫ | |||
{{Docnav|[[Part_Cylinder|Cylinder]]|[[Part_Torus|Torus]]|[[Part_Module|Part]]|IconL=Part_Cylinder.png|IconC=Workbench_Part.svg|IconR=Part_Torus.png}} |
|||
<div class="mw-translate-fuzzy"> |
|||
{{GuiCommand/cs|Name=Part Sphere|Name/cs=Díl Koule|MenuLocation=Díl -> Koule||Workbenches=[[Part_Module/cs|Modul Díl]], Kompletace|SeeAlso=[[Part_CreatePrimitives/cs|Díl Vytváření zákl.geom.tvarů]]}} |
{{GuiCommand/cs|Name=Part Sphere|Name/cs=Díl Koule|MenuLocation=Díl -> Koule||Workbenches=[[Part_Module/cs|Modul Díl]], Kompletace|SeeAlso=[[Part_CreatePrimitives/cs|Díl Vytváření zákl.geom.tvarů]]}} |
||
</div> |
|||
Vytvoří jednoduchou parametrickou kouli podle parametrů pozice, úhel1, úhel2, úhel3 a poloměr. |
Vytvoří jednoduchou parametrickou kouli podle parametrů pozice, úhel1, úhel2, úhel3 a poloměr. |
||
[[File:SimpleSphere.jpg|400px]] |
|||
<div class="mw-translate-fuzzy"> |
|||
== Použití == |
== Použití == |
||
V pracovní ploše [[Part_Workbench/cs|Díl]] klikněte na ikonu koule [[Image:Part Sphere.png|32px]]. |
V pracovní ploše [[Part_Workbench/cs|Díl]] klikněte na ikonu koule [[Image:Part Sphere.png|32px]]. |
||
Koule bude při vytvoření umístěna do počátečního bodu (bod 0,0,0). Parametry úhly dovolují vytvořit částečnou kouli místo celé koule (defaultně jsou nastaveny na 360°) |
Koule bude při vytvoření umístěna do počátečního bodu (bod 0,0,0). Parametry úhly dovolují vytvořit částečnou kouli místo celé koule (defaultně jsou nastaveny na 360°) |
||
</div> |
|||
== Volby == |
== Volby == |
||
Line 23: | Line 32: | ||
====Parameter==== |
====Parameter==== |
||
* {{Parameter|Radius:}} Radius of the sphere |
* {{Parameter|Radius:}} Radius of the sphere |
||
* {{Parameter|Angle 1:}} 1nd angle to cut / define the sphere |
|||
* {{Parameter|Angle 1:}} Angle defined between the y-axis (green arrow) and an imaginary rotating line around the x-axis (red arrow). One end of the line is fixed on the origin. The other end of the line may rotate as said around the x-axis and remain in the XY-plane. The line has the length of the radius of the sphere. |
|||
* {{Parameter|Angle 2:}} |
* {{Parameter|Angle 2:}} 2nd angle to cut / define the sphere |
||
* {{Parameter|Angle 3:}} 3rd angle to cut / define the sphere |
|||
Because it is quite difficult to explain the meaning of the parameters angle 1, angle 2, angle 3, the picture below gives an explanation about these parameters with following values: angle 1 = -45°, angle 2 = 45° and angle 3= 90°. |
|||
[[File:SphereCutThreeAngles.jpg|400px]] |
|||
{{clear}} |
{{clear}} |
||
⚫ | |||
{{Docnav|[[Part_Cylinder|Cylinder]]|[[Part_Torus|Torus]]|[[Part_Module|Part]]|IconL=Part_Cylinder.png|IconC=Workbench_Part.svg|IconR=Part_Torus.png}} |
|||
{{Part Tools navi}} |
|||
{{Userdocnavi}} |
Revision as of 14:17, 13 February 2019
Díl Koule |
Umístění Menu |
---|
Díl -> Koule |
Pracovní stoly |
Modul Díl, Kompletace |
Výchozí zástupce |
Nikdo |
Představen ve verzi |
- |
Viz také |
Díl Vytváření zákl.geom.tvarů |
Vytvoří jednoduchou parametrickou kouli podle parametrů pozice, úhel1, úhel2, úhel3 a poloměr.
Použití
V pracovní ploše Díl klikněte na ikonu koule . Koule bude při vytvoření umístěna do počátečního bodu (bod 0,0,0). Parametry úhly dovolují vytvořit částečnou kouli místo celé koule (defaultně jsou nastaveny na 360°)
Volby
The parametric sphere is defined by the following parameters:
- Radius
- Angle 1
- Angle 2
- Angle 3
- as well as the standard set of placement parameters
The picture below gives an overview of a parametric sphere with parameters different from the default value.
Parameter
- Radius: Radius of the sphere
- Angle 1: 1nd angle to cut / define the sphere
- Angle 2: 2nd angle to cut / define the sphere
- Angle 3: 3rd angle to cut / define the sphere
Because it is quite difficult to explain the meaning of the parameters angle 1, angle 2, angle 3, the picture below gives an explanation about these parameters with following values: angle 1 = -45°, angle 2 = 45° and angle 3= 90°.
Part
- Primitives: Box, Cylinder, Sphere, Cone, Torus, Tube, Create primitives, Shape builder
- Creation and modification: Extrude, Revolve, Mirror, Fillet, Chamfer, Make face from wires, Ruled Surface, Loft, Sweep, Section, Cross sections, 3D Offset, 2D Offset, Thickness, Projection on surface, Attachment
- Boolean: Make compound, Explode Compound, Compound Filter, Boolean, Cut, Fuse, Common, Connect, Embed, Cutout, Boolean fragments, Slice apart, Slice, XOR
- Measure: Measure Linear, Measure Angular, Measure Refresh, Clear All, Toggle All, Toggle 3D, Toggle Delta
User documentation
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web
- Hubs: User hub, Power users hub, Developer hub