PartDesign Revolution/fr: Difference between revisions
No edit summary |
(Updating to match new version of source page) |
||
Line 37: | Line 37: | ||
===Angle=== |
===Angle=== |
||
This controls the angle through which the revolution is to be formed, e.g. 360° would be a full, contiguous revolution. |
This controls the angle through which the revolution is to be formed, e.g. 360° would be a full, contiguous revolution. |
||
The images in the [[#Examples|examples]] section demonstrate some of the possibilities with specifying different angles. It is not possible to specify negative angles (use the '''Reversed''' option instead) or angles greater than 360°. |
The images in the [[#Examples|examples]] section demonstrate some of the possibilities with specifying different angles. It is not possible to specify negative angles (use the '''Reversed''' option instead) or angles greater than 360° . |
||
===Symmetric to plane=== |
===Symmetric to plane=== |
||
If checked, the revolution will extend half of the specified angle in both directions from the sketch plane. |
If checked, the revolution will extend half of the specified angle in both directions from the sketch plane. |
||
Line 45: | Line 45: | ||
{{clear}} |
{{clear}} |
||
==Properties== |
==Properties == |
||
Below are properties which can be defined after creation of the feature. Data properties Base, Axis and Angle are uneditable. |
Below are properties which can be defined after creation of the feature. Data properties ''Base'', ''Axis'' and ''Angle'' are uneditable. |
||
* {{PropertyData|Label}}: |
* {{PropertyData|Label}}: label given to the operation, can be changed at convenience. |
||
* {{PropertyData|Midplane}}: true or false. See [[#Symmetric to plane|Symmetric to plane]]. |
* {{PropertyData|Midplane}}: true or false. See [[#Symmetric to plane|Symmetric to plane]]. |
||
* {{PropertyData|Reversed}}: true or false. See [[#Reversed|Reversed]]. |
* {{PropertyData|Reversed}}: true or false. See [[#Reversed|Reversed]]. |
Revision as of 08:23, 17 March 2018
Révolution |
Emplacement du menu |
---|
Part Design → Révolution |
Ateliers |
PartDesign, Complet |
Raccourci par défaut |
Aucun |
Introduit dans la version |
- |
Voir aussi |
Aucun |
Introduction
Cet outil produit un solide par révolution d'une esquisse ou d'un objet 2D sélectionné autour d'un axe donné.
Ci-dessus : l'esquisse (A) est révolutionnée de 270 degrés dans le sens antihoraire autour de l'axe (B) ; le solide résultant (C) est montré à droite.
Utilisation
- Sélectionner l'esquisse à révolutionner. v0.17 et ultérieures Une face du solide peut également être utilisée.
- Appuyer sur le bouton Révolution.
- Définir les paramètres de la révolution (voir la section suivante).
- Appuyer sur le bouton OK.
Options
Lors de la création de la révolution, la vue combinée bascule automatiquement à l'onglet Tâches, qui affiche le dialogue "Paramètres de la révolution". Plusieurs paramètres permettent de définir comment l'esquisse sera révolutionnée.
AxeCette option spécifie l'axe autour duquel l'esquisse doit être tournée.
AngleDétermine la valeur de la rotation, par exemple, 360 ° seraient, une révolution complète . Les images dans la section exemples montrent que|lques-unes des possibilités avec des angles différents . Il n'est pas possible de spécifier des angles négatifs (utiliser l'option Inversée à la place) ou des angles supérieurs à 360 °. Symétrique au planLa révolution s'étendra de la moitié de l'angle spécifié dans les deux directions symétriques au plan d'esquisse. InverséeLa direction de la révolution sera inversée AngleThis controls the angle through which the revolution is to be formed, e.g. 360° would be a full, contiguous revolution. The images in the examples section demonstrate some of the possibilities with specifying different angles. It is not possible to specify negative angles (use the Reversed option instead) or angles greater than 360° . Symmetric to planeIf checked, the revolution will extend half of the specified angle in both directions from the sketch plane. ReversedIf checked, the direction of revolution is reversed from default clockwise to counterclockwise. |
Properties
Below are properties which can be defined after creation of the feature. Data properties Base, Axis and Angle are uneditable.
- DonnéesLabel: label given to the operation, can be changed at convenience.
- DonnéesMidplane: true or false. See Symmetric to plane.
- DonnéesReversed: true or false. See Reversed.
- DonnéesRefine: v0.17 and above true or false. If set to true, cleans the solid from residual edges left by features. See Part RefineShape for more details.
Exemples
Liens utiles
Un exemple d'utilisation détaillé sur le forum (en anglais).