PartDesign Pad/es: Difference between revisions

From FreeCAD Documentation
(Created page with "frame|left")
(Created page with "===Dimension=== Introduce un valor numérico para la longitud del saliente. La dirección por defecto para la extrusión es saliendo del soporte, pero se puede cambiar selecc...")
Line 21: Line 21:
[[Image:pad_parameters_cropped_es.png|frame|left]]
[[Image:pad_parameters_cropped_es.png|frame|left]]


===Type===
===Dimension===

Type offers five different ways of specifying the length to which the pad will be extruded.
Introduce un valor numérico para la longitud del saliente. La dirección por defecto para la extrusión es saliendo del soporte, pero se puede cambiar seleccionando la opción '''Invertir'''. Las extrusiones se realizan normales [http://en.wikipedia.org/wiki/Surface_normal normales] al plano de definición del croquis.
====Dimension====

Enter a numeric value for the length of the pad. The default direction for extrusion is away (outside of) the support, but it can be changed by ticking the '''Reversed''' option. Extrusions occur [http://en.wikipedia.org/wiki/Surface_normal normal] to the defining sketch plane. With the option '''Symmetric to plane''' the pad will extend half of the given length to either side of the sketch plane. Negative dimensions are not possible. Use the '''Reversed''' option instead.
Con la opción '''Simétrico al plano''' el saliente se extenderá la mitad de la dimensión indicada hacia cada lado del plano de croquis.
====Two dimensions====

This allows to enter a second length in which the pad should extend in the opposite direction (into the support). Again can be changed by ticking the '''Reversed''' option.
No es posible indicar dimensiones negativas. Utiliza en cambio la opción '''invertir'''.
====To last====

The pad will extrude up to the last face of the support in the extrusion direction. If there is no support, an error message will appear.
====To first====
===Dos dimensiones===

The pad will extrude up to the first face of the support in the extrusion direction. If there is no support, an error message will appear.
Permite introducir una segunda longitud en la cual el saliente debería extenderse en la dirección opuesta (dentro del soporte). De nuevo se puede cambiar seleccionado la opción '''invertir'''.
====Up to face====

The pad will extrude up to a face in the support that can be chosen by clicking on it. If there is no support, no selections will be accepted.
===Hasta el último===

El saliente se extruirá hasta la última cara del soporte en la dirección de extrusión. Si no existe soporte, se mostrará un mensaje de error.

===Hasta el primero===

El saliente se extruirá hasta la primera cara del soporte en la dirección de extrusión. Si no existe soporte, se mostrará un mensaje de error.

===Hasta la cara===

El saliente se extruirá hasta una cara del soporte que puede seleccionarse designándola. Si no existe soporte, no se aceptará ninguna selección.


===Length===
===Length===

Revision as of 02:33, 1 August 2014

PartDesign_Pad

Ubicación en el Menú
Diseño de Piezas -> Saliente
Entornos de trabajo
Diseño de Piezas, Complete
Atajo de teclado por defecto
Ninguno
Introducido en versión
-
Ver también
Ninguno

Introducción

'Crea un saliente a partir de un croquis seleccionado' - Esta herramienta toma un croquis seleccionado como entrada (el 'croquis de definición'), y crea a partir de él un 'saliente'. Un saliente es esencialmente una extrusión de un croquis. Por ejemplo, si un croquis estuviera formados por dos circunferencias concéntricas, y se utilizase la herramienta Saliente sobre dicho croquis, el resultado sería un cilindro:

If the selected sketch is mapped to the face of an existing solid or another Part Design feature, the pad will be fused to it.

How to use

  1. Select the sketch to be padded.
  2. Press the Pad button.
  3. Set the Pad parameters (see next section).
  4. Click OK.

Opciones

Cuando se crea un saliente, el letrero de diálogo de los 'parámetros del saliente' ofrece cinco diferentes formas de especificar la longitud a la cual el saliente se va a extruir

Dimension

Introduce un valor numérico para la longitud del saliente. La dirección por defecto para la extrusión es saliendo del soporte, pero se puede cambiar seleccionando la opción Invertir. Las extrusiones se realizan normales normales al plano de definición del croquis.

Con la opción Simétrico al plano el saliente se extenderá la mitad de la dimensión indicada hacia cada lado del plano de croquis.

No es posible indicar dimensiones negativas. Utiliza en cambio la opción invertir.

Dos dimensiones

Permite introducir una segunda longitud en la cual el saliente debería extenderse en la dirección opuesta (dentro del soporte). De nuevo se puede cambiar seleccionado la opción invertir.

Hasta el último

El saliente se extruirá hasta la última cara del soporte en la dirección de extrusión. Si no existe soporte, se mostrará un mensaje de error.

Hasta el primero

El saliente se extruirá hasta la primera cara del soporte en la dirección de extrusión. Si no existe soporte, se mostrará un mensaje de error.

Hasta la cara

El saliente se extruirá hasta una cara del soporte que puede seleccionarse designándola. Si no existe soporte, no se aceptará ninguna selección.

Length

Defines the length of the pad. Multiple units can be used independently of the user's units preferences (m, cm, mm, nm, ft or ', in or ").

Symmetric to plane

Tick the checkbox to extend half of the given length to either side of the sketch plane.

Reversed

Reverses the direction of the pad.

Limitations

  • Like all Part Design features, Pad creates a solid, thus the sketch must include a closed profile or it will fail. There can be multiple enclosed profiles inside a larger one, provided none intersect each other (for example, a rectangle with two circles inside it).
  • The algorithm used for To First and To Last is:
    • Create a line through the centre of gravity of the sketch
    • Find all faces of the support cut by this line
    • Choose the face where the intersection point is nearest/furthest from the sketch
  • This means that the face that is found might not always be what you expected. If you run into this problem, use the Up to face type instead, and pick the face you want.
  • For the very special case of extrusion to a concave surface, where the sketch is larger than this surface, extrusion will fail. This is a unresolved bug.
  • There is no automatic cleanup, e.g. of adjacent planar surfaces into a single surface. You can fix this manually in the Part workbench with Refine shape (which creates an unlinked, non-parametric solid) or with the "Refine shape feature" (which creates a parametric feature) from the OpenSCAD Workbench.