Manual:Navigating in the 3D view/de: Difference between revisions

From FreeCAD Documentation
(Created page with "Das Navigieren in der FreeCAD 3D Ansicht kann mit einer Maus, einem 3D Mausnavigator Gerät, der Tastatur, einem Touchpad oder einer Kombination aus beidem erfolgen. FreeCAD i...")
(Created page with "Jeder dieser Modi ordnet diesen vier Operationen unterschiedliche Maustasten oder Maus + Tastatur-Kombinationen oder Mausgesten zu. Die folgende Tabelle zeigt die wichtigsten...")
Line 33: Line 33:
[[Image:FreeCAD-v0-18-NavigationModePopup.png]]
[[Image:FreeCAD-v0-18-NavigationModePopup.png]]


Jeder dieser Modi ordnet diesen vier Operationen unterschiedliche Maustasten oder Maus + Tastatur-Kombinationen oder Mausgesten zu. Die folgende Tabelle zeigt die wichtigsten verfügbaren Modi:
Each of these modes allocates different mouse buttons, or mouse + keyboard combinations, or mouse gestures, to these four operations. The following table shows the principal available modes:


{| class="wikitable" style=" width: 100%;text-align:center;"
{| class="wikitable" style=" width: 100%;text-align:center;"

Revision as of 13:49, 18 January 2020

Ein Wort zum 3D Raum

Wenn dies dein erster Kontakt mit einer 3D Anwendung ist, musst du dich zuerst mit einigen Konzepten vertraut machen. Wenn nicht, kannst du diesen Abschnitt sicher überspringen.

Der FreeCAD 3D Raum ist ein Euklidischer Raum. Er hat einen Ursprungspunkt und drei Achsen: X, Y und Z. Wenn du deine Szene von oben betrachtest, zeigt die X Achse konventionell nach rechts, die Y Achse nach hinten und die Z Achse nach oben. In der unteren rechten Ecke der FreeCAD Ansicht kannst Du immer sehen, von wo aus du die Szene betrachtest:

Der Punkt, an dem sich die drei Achsen treffen, ist der Ursprung. Es ist der Punkt, an dem der Wert aller Koordinaten Null ist. Für jede beliebige Achse wird bei Bewegung in einer Richtung der Koordinatenwert erhöht und bei Bewegung in der entgegengesetzten Richtung verringert sich der Koordinatenwert. Jeder Punkt jedes im 3D-Raum vorhandenen Objekts kann über seine (x, y, z) Koordinaten lokalisiert werden. Zum Beispiel wird ein Punkt mit den Koordinaten (2, 3, 1) bei +2 Einheiten auf der X-Achse, +3 Einheiten auf der Y-Achse und +1 Einheit auf der Z-Achse liegen:

Du kannst diese Szene aus jedem Winkel betrachten, als ob du eine Kamera in der Hand hättest. Diese Kamera kann nach links, rechts, oben und unten bewegt (schwenken), um das, worauf sie zeigt, gedreht (drehen) und näher an die Szene herangeführt oder von ihr entfernt werden (zoomen).

Die FreeCAD 3D Ansicht

Mausnavigation

Das Navigieren in der FreeCAD 3D Ansicht kann mit einer Maus, einem 3D Mausnavigator Gerät, der Tastatur, einem Touchpad oder einer Kombination aus beidem erfolgen. FreeCAD implementiert mehrere Navigationsmodi, die die drei grundlegenden Operationen zur Steuerung der Ansicht (Schwenken, Drehen und Zoomen) sowie die Auswahl von Objekten auf dem Bildschirm bestimmen. Die Navigationsmodi werden über den Bildschirm "Einstellungen" oder direkt durch einen Rechtsklick auf eine beliebige Stelle in der 3D-Ansicht aufgerufen:

Jeder dieser Modi ordnet diesen vier Operationen unterschiedliche Maustasten oder Maus + Tastatur-Kombinationen oder Mausgesten zu. Die folgende Tabelle zeigt die wichtigsten verfügbaren Modi:

Mode Pan Rotate Zoom Select
OpenInventor Click middle button mouse Click left button mouse Roll middle button mouse hold CTRL + drag Click left button mouse
CAD (default) Click middle button mouse or Click right button mouse + CTRL key Hold middle then left mouse button or Click right button mouse + SHIFT key Roll middle button mouse or Click right button mouse + CTRL + SHIFT key Click left button mouse
Blender hold SHIFT + drag Click middle button mouse or drag Click left + right button mouse and drag Click middle button mouse Roll middle button mouse Click left button mouse
Touchpad hold SHIFT + drag Touchpad (mouse) pointer ALT + Touchpad (mouse) pointer PGUP / PGDOWN Click touchpad (mouse) left button
Gesture drag Click right button mouse drag Click left button mouse Roll middle button mouse Click left button mouse
OpenCascade Click middle button mouse Hold middle then right mouse button Roll middle button mouse Click left button mouse

Keyboard Navigation

Alternatively, some keyboard controls are always available, no matter the navigation mode:

  • CTRL + and CTRL - to zoom in and zoom out
  • The arrow keys to shift the view left/right and up/down
  • SHIFT + left arrow and SHIFT + right arrow to rotate the view by 90 degrees
  • the numeric keys, 0 to 6, for the seven standard views: isometric, front, top, right, rear, bottom, and left
  • VO will set the camera in orthographic mode,
  • while VP sets it in perspective mode.
  • CTRL will allow you to select more than one object or element

These controls are also available from the View menu and some from the View toolbar.

Using the Navigation Cluster

In the default setup, there is a Navigation Cluster in the upper right corner of the 3D display. This may be used to rotate the displayed object by a fixed amount, reset the display to one of several standard views, and change the display mode.

When using the navigation cluster, a control point will turn light blue when the pointer is hovering over a sensitive area. If the area below the pointer does not change color, clicking on it will have no affect. As of this writing (v0.18), there are some registration issues which prevent all parts of some control points from being active.

Clicking on a face will switch the view to that face; clicking on a corner will switch to a view with that corner pointing towards you.

Clicking one of the four triangles will rotate the view 45 degrees in the indicated direction. Clicking one of the two curved arrows at the top will rotate the view 45 degrees in the indicated direction around a line pointing towards you.

The navigation cluster may be moved to any part of the 3D display by dragging. The drag (left) mouse button must be pressed inside the cube itself to initiate a drag. The structure will not begin moving until the pointer is dragged outside the cube.

There is a smaller mini-cube in the lower right of the cluster which activates a drop-down menu allowing you to switch the viewing mode.

Selecting objects

Objects in the 3D view can be selected by clicking them with the corresponding mouse button, depending on the navigation mode (described above). A single click will select the object and one of its subcomponents (edge, face, vertex). Double-clicking will select the object and all its subcomponents. You can select more than one subcomponent, or even different subcomponents from different objects, by pressing the CTRL key. Clicking with the selection button on an empty portion of the 3D view will deselect everything.

A panel called "Selection view", available from the View menu, can also be turned on, which shows you what is currently selected:

You can also use the Selection View to select objects by searching for a particular object.

Read more