# Difference between revisions of "Draft Snap/sv"

(Updating to match new version of source page) |
(Updating to match new version of source page) |
||

Line 3: | Line 3: | ||

[[Image:Draft_Snap_example.jpg]] | [[Image:Draft_Snap_example.jpg]] | ||

− | + | ==Available snap locations== | |

− | + | * [[Image:Snap_Midpoint.png|32px]] [[Draft_Midpoint|Midpoint]]: the middle point of line and arc segments | |

− | + | * [[Image:Snap_Perpendicular.png|32px]] [[Draft_Perpendicular|Perpendicular]]: on line and arc segments, perpendicularly to the latest point | |

− | + | * [[Image:Snap_Grid.png|32px]] [[Draft_ToggleGrid|Grid]]: the nodes of the Draft grid, if visible. | |

− | + | * [[Image:Snap_Intersection.png|32px]] [[Draft_Intersection|Intersection]]: the intersection of 2 line or arc segments. Hover the mouse over the two desired bjects to activate their intersection snaps | |

+ | * [[Image:Snap_Parallel.png|32px]] [[Draft_Parallel|Parallel]]: on an imaginary line parallel to a line segment. Hover the mouse over the desired object to activate its parallel snap | ||

+ | * [[Image:Snap_Endpoint.png|32px]] [[Draft_Endpoint|Endpoint]]: the endpoints of line, arc and spline segments | ||

+ | * [[Image:Snap_Angle.png|32px]] [[Draft_Angle|Angle]]: the special cardinal points of circles and arcs, at 45° and 90° | ||

+ | * [[Image:Snap_Center.png|32px]] [[Draft_Center|Center]]: the center point of arcs and circles | ||

+ | * [[Image:Snap_Extension.png|32px]] [[Draft_Extension|Extension]]: on an imaginary line that extends beyond the endpoints of line segments. Hover the mouse over the desired object to activate its extension snap | ||

+ | * [[Image:Snap_Near.png|32px]] [[Draft_Near|Near]]: the closest point on the nearest object | ||

+ | * [[Image:Snap_Ortho.png|32px]] [[Draft_Ortho|Ortho]]: on imaginary lines that cross the last point, and extend at 0°, 45° and 90° | ||

+ | * [[Image:Snap_Dimensions.png|32px]] [[Draft_Dimensions|Dimensions]] | ||

+ | * [[Image:Snap_WorkingPlane.png|32px]] [[Draft_WorkingPlane|Restrict to working plane]]: always places the snapped point on the current [[Draft SelectPlane|working plane]], even if you snap to a point outside that working plane. | ||

==Options== | ==Options== | ||

− | * [[Image:Snap_Lock.png|32px]] | + | * [[Image:Snap_Lock.png|32px]] [[Draft ToggleSnap|Lock]]: turns snapping on/off globally |

* Certain additional snap locations can be obtained by combining 2 snap locations, such as ortho + extension, that will give you a snap point at the intersection of their imaginary lines. | * Certain additional snap locations can be obtained by combining 2 snap locations, such as ortho + extension, that will give you a snap point at the intersection of their imaginary lines. | ||

* Other, more complex snap locations can also be obtained by using [[Draft Constrain|constraining]] (by pressing {{KEY|SHIFT}} or {{KEY|X}} or {{KEY|Y}} or {{KEY|Z}} while drawing). | * Other, more complex snap locations can also be obtained by using [[Draft Constrain|constraining]] (by pressing {{KEY|SHIFT}} or {{KEY|X}} or {{KEY|Y}} or {{KEY|Z}} while drawing). |

## Revision as of 09:58, 1 August 2014

Snäppa innebär att din nästa 3d punkt "klistras" på en existerande punkt.

## Available snap locations

- Midpoint: the middle point of line and arc segments
- Perpendicular: on line and arc segments, perpendicularly to the latest point
- Grid: the nodes of the Draft grid, if visible.
- Intersection: the intersection of 2 line or arc segments. Hover the mouse over the two desired bjects to activate their intersection snaps
- Parallel: on an imaginary line parallel to a line segment. Hover the mouse over the desired object to activate its parallel snap
- Endpoint: the endpoints of line, arc and spline segments
- Angle: the special cardinal points of circles and arcs, at 45° and 90°
- Center: the center point of arcs and circles
- Extension: on an imaginary line that extends beyond the endpoints of line segments. Hover the mouse over the desired object to activate its extension snap
- Near: the closest point on the nearest object
- Ortho: on imaginary lines that cross the last point, and extend at 0°, 45° and 90°
- Dimensions
- Restrict to working plane: always places the snapped point on the current working plane, even if you snap to a point outside that working plane.

## Options

- Lock: turns snapping on/off globally
- Certain additional snap locations can be obtained by combining 2 snap locations, such as ortho + extension, that will give you a snap point at the intersection of their imaginary lines.
- Other, more complex snap locations can also be obtained by using constraining (by pressing SHIFT or X or Y or Z while drawing).
- Pressing L while drawing locks the current angle of the line segment being drawn.
- The maximum distance at which a point is snapped a snap location is specified in the preferences, and can also be changed on-the-fly by pressing [ or ] keys.