Draft Constrain/fr: Difference between revisions
(Updating to match new version of source page) |
(Updating to match new version of source page) |
||
| Line 1: | Line 1: | ||
<languages/> |
<languages/> |
||
{{docnav|[[Draft Coordinates|Coordinates]]|[[Draft Snap|Snapping]]|[[Draft_Module|Draft_Module]]}} |
|||
<div class="mw-translate-fuzzy"> |
|||
Pour contraindre, appuyer sur {{KEY|SHIFT}} pendant le dessin. |
Pour contraindre, appuyer sur {{KEY|SHIFT}} pendant le dessin. |
||
</div> |
|||
However, when these parameters need to be precise, it is possible to enter the exact [[Draft Coordinates]] in the dialog for the tool. |
|||
Another way of selecting more precise points is by constraining the movement of the pointer to a particular X, Y, or Z direction. |
|||
== Horizontal and vertical constraints == |
|||
[[Image:Draft_Constrain_example.jpg]] |
[[Image:Draft_Constrain_example.jpg]] |
||
{{Caption|Perpendicular lines that were created by constraining the position of the points orthogonally}} |
|||
Hold the {{KEY|Shift}} key while drawing to force the next point to be constrained horizontally (X direction) or vertically (Y direction) in relation to the last point entered. The horizontal or vertical orientation depends on the position of the pointer when you press {{KEY|Shift}}; if you are more east or west from the last point, it will be horizontal; if you are more north or south, it will be vertical. To change the orientation, just release {{KEY|Shift}}, move the pointer to a new location, and hold {{KEY|Shift}} again. |
|||
Dans tous les outils qui supportent le mode contrainte, vous pouvez contraindre le prochain point verticalement ou horizontalement en relation avec le dernier point effectué. La contrainte verticale ou horizontale dépend de l'endroit où le pointeur de la souris se situe lorsque vous appuyez sur {{KEY|SHIFT}}. Si le pointeur est au nord ou au sud du dernier point, la contrainte sera verticale. S'il est à l'ouest ou à l'est, elle sera horizontale. Pour modifier, il suffit de relâcher {{KEY|SHIFT}} et d'appuyer à nouveau à un nouvel endroit. |
|||
Some tools like [[Draft Offset]] and [[Draft Trimex]] use constraining differently. They do not constrain vertically or horizontally but use a different method more adapted to the particular tool, for example, constraining the operation to a certain line segment. |
|||
Certains outils, comme le [[Draft_Offset/fr|décalage]] et [[Draft_Trimex/fr|découper/prolonger]] utilisent les contraintes différemment. Ils ne contraignent pas verticalement ou horizontalement, mais utilise une méthode plus adaptée, comme par exemple contraindre une opération à un segment de polyligne particulier. |
|||
While constraining the movement of the pointer, the Taskview panel will lock the coordinate values that are not being modified. For example, if using a horizontal constraint, only the X value changes, while the Y and Z values remain at their original relative or absolute coordinates, depending on whether relative mode is active or not. |
|||
| ⚫ | |||
[[Image:Draft_Constrain_Shift_Taskview_example.png]] |
|||
{{Caption|Taskview when using a horizontal constraint while holding the Shift key}} |
|||
== X, Y, Z constraints == |
|||
Press one of the {{KEY|X}}, {{KEY|Y}} or {{KEY|Z}} keys after a point to constrain the next point on the specified X, Y, or Z direction. Press the same key again to release the constraint. |
|||
Pressing {{KEY|X}} or {{KEY|Y}} is equivalent to holding {{KEY|Shift}} and constraining horizontally or vertically, respectively. |
|||
[[Image:Draft_Constrain_Y_Taskview_example.png]] |
|||
{{Caption|Taskview when using a vertical constraint after pressing the Y key}} |
|||
<div class="mw-translate-fuzzy"> |
|||
| ⚫ | |||
</div> |
|||
{{clear}} |
{{clear}} |
||
Revision as of 16:34, 5 February 2019
Pour contraindre, appuyer sur SHIFT pendant le dessin.
However, when these parameters need to be precise, it is possible to enter the exact Draft Coordinates in the dialog for the tool.
Another way of selecting more precise points is by constraining the movement of the pointer to a particular X, Y, or Z direction.
Horizontal and vertical constraints
Perpendicular lines that were created by constraining the position of the points orthogonally
Hold the Shift key while drawing to force the next point to be constrained horizontally (X direction) or vertically (Y direction) in relation to the last point entered. The horizontal or vertical orientation depends on the position of the pointer when you press Shift; if you are more east or west from the last point, it will be horizontal; if you are more north or south, it will be vertical. To change the orientation, just release Shift, move the pointer to a new location, and hold Shift again.
Some tools like Draft Offset and Draft Trimex use constraining differently. They do not constrain vertically or horizontally but use a different method more adapted to the particular tool, for example, constraining the operation to a certain line segment.
While constraining the movement of the pointer, the Taskview panel will lock the coordinate values that are not being modified. For example, if using a horizontal constraint, only the X value changes, while the Y and Z values remain at their original relative or absolute coordinates, depending on whether relative mode is active or not.
File:Draft Constrain Shift Taskview example.png
Taskview when using a horizontal constraint while holding the Shift key
X, Y, Z constraints
Press one of the X, Y or Z keys after a point to constrain the next point on the specified X, Y, or Z direction. Press the same key again to release the constraint.
Pressing X or Y is equivalent to holding Shift and constraining horizontally or vertically, respectively.
Taskview when using a vertical constraint after pressing the Y key