Arch: Rebar LShape/Armătura în L

UShape Rebar

Bent Shape Rebar

Arch

Arch Rebar LShape
poziția meniului
Arch → Rebar tools
Ateliere
Arch, BIM
scurtătură
nici unul
Prezentat în versiune
0.17
A se vedea, de asemenea,
Bent Rebar, Rebar

Descriere

Instrumentul LShape Rebar permite utilizatorului să creeze o armătură LShape reinforcing bar în elementele structurale.

This tool is part of the Reinforcement Workbench, an external workbench that can be installed with the Addon Manager.

Cum se folosește

1. Create a structure element
2. Select any face of the structure
3. Then select LShape Rebar from the rebar tools
4. A task panel will pop-out on the left side of the screen as shown below
5. Select the desired orientation
6. Give the inputs like front cover, left side cover, right side cover, bottom cover, top cover, rounding and diameter of the rebar
7. Select the mode of distribution either amount or spacing
8. If spacing is selected, a user can also opt for custom spacing
9. Pick selected face is used to verify or change the face for rebar distribution
10. Click OK or Apply to generate the rebars
11. Click Cancel to exit the task panel

Task panel for the tool

Proprietăți

• DateOrientation: Stabilește orientarea armăturii (ca de ex jos, sus, dreapta și stânga).
• DateFront Cover: Distanța dintre armături și fațetele selectate.
• DateRight Cover: Distanța între capătul dintre capătul dreapta al armăturii și fațeta dreapta a structurii.
• DateLeft Cover: Distanța dintre capătul din stânga al armăturii și fațeta stângă a structurii
• DateBottom Cover: Distanța dintre armătură și fațeta de jos a structurii.
• DateTop Cover: Distanța dintre armătură și fața superioară a structurii.
• DateRounding: o valoarea a racordării de aplicat la colțutile barelor , exprimată în raport cu diametrul acestora.
• DateAmount: Cantitatea de armătură
• DateSpacing: Distanța dintre acele fiecărei bare.

Scrip-Programare

See also: Arch API, Reinforcement API and FreeCAD Scripting Basics.

The LShape Rebar tool can by used in macros and from the python console by using the following function:

Rebar = makeLShapeRebar(f_cover, b_cover, l_cover, r_cover,
                        diameter, t_cover, rounding, amount_spacing_check, amount_spacing_value, orientation="Bottom Left",
                        structure=None, facename=None):

• O armătură tip LShape Rebar are patru orientări diferite:
  • Bottom Right
  • Bottom Left
  • Top Right
  • Top Left
• Adaugă obiectul LShape reinforcing bar la obiectul structural selectat.
• Dacă nu este dată nici o Structură și nici o Facename, ea va avea ca intrare fațeta selectat de utilizator.
• Aici argumentul CoverAlong este de tip tuplă.
• Returnează noul obiect Rebar.

Example

import FreeCAD, Arch, LShapeRebar

Structure = Arch.makeStructure(length=1000, width=1000, height=400)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()

Rebar = LShapeRebar.makeLShapeRebar(50, 20, 20, 20,
                                    8, 50, 4, True, 6, "Bottom Left", Structure, "Face4")
Rebar.ViewObject.ShapeColor = (0.9, 0.0, 0.0)

Rebar2 = LShapeRebar.makeLShapeRebar(50, 50, 20, 20,
                                     8, 50, 4, True, 6, "Bottom Left", Structure, "Face6")
Rebar2.ViewObject.ShapeColor = (0.0, 0.0, 0.9)

Edition of the rebar

You can change the properties of the rebar with the following function:

editLShapeRebar(Rebar, f_cover, b_cover, l_cover, r_cover,
                diameter, t_cover, rounding, amount_spacing_check, amount_spacing_value, orientation,
                structure=None, facename=None)

• Rebar is a previously created LShapeRebar object.
• The other parameters are the same as required by the makeLShapeRebar() function.
• structure and facename may be omitted so that the rebar stays in the original structure.

import LShapeRebar

LShapeRebar.editLShapeRebar(Rebar, 50, 50, 20, 20,
                            12, 50, 6, True, 5, "Top Right")

LShapeRebar.editLShapeRebar(Rebar2, 50, 50, 20, 20,
                            12, 70, 6, True, 5, "Top Right")

UShape Rebar

Bent Shape Rebar

Arch

Arch

• Elements: Wall, Structure, Curtain Wall, Window, Roof, Space, Stairs, Equipment, Frame, Fence, Truss, Profile, Pipe, Pipe Connector
• Reinforcements: Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement, Custom Rebar
• Panels: Panel, Panel Cut, Panel Sheet, Nest
• Materials: Material, Multi-Material
• Organization: Building Part, Project, Site, Building, Level, External reference, Section Plane, Schedule
• Axes: Axis, Axes system, Grid

---

• Modification: Cut with plane, Add component, Remove component, Survey

---

• Utilities: Component, Clone component, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, 3 Views from mesh, Create IFC spreadsheet, Toggle Subcomponents
• Additional: Preferences, Import Export Preferences (IFC, DAE, OBJ, JSON, 3DS, SHP), IfcOpenShell, IfcPlusPlus, Arch API

User documentation

• Getting started
• Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
• Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate

---

• Help: Tutorials, Video tutorials
• Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web

---

• Addons: Addon Manager, External workbenches, Scripting and macros

---

• Hubs: User hub, Power users hub, Developer hub