|Arch → Rebar|
|Introduced in version|
|Arch Structure, Reinforcement Addon|
Rebar objects are based on 2D profiles such as Draft objects and Sketches, that must be drawn on a face of the structural object. After creation you can adjust the properties of the rebar, including the number and diameter of the bars, and the offset distance between them and the faces of the structural element.
Structural object with two sketches drawn on its faces, which are then turned into two sets of rebar objects
How to use
- Create an element.
- Switch to the Sketcher Workbench.
- Select one face of the structural element.
- Press the button to start a new sketch on the selected face.
- Draw the diagram of your bar.
- Press the button to finish.
- Switch back to the Arch Workbench.
- Select the sketch you just drew.
- Press the button, or press then keys.
- Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element).
Although normally a rebar is used inside an Arch Structure, since FreeCAD 0.19 the rebar can be created outside of any host object. To host a rebar inside an object, you just need to set its DATAHost.
- Rebars share the common properties and behaviours of all Arch Components
- The rounding value is expressed in times the diameter. If your bar has a diameter of 5mm, a rounding value of 3 will create rounding at angles with a radius of 15mm.
- Default values for new rebars can be set in the Arch preferences settings.
- If a direction vector is not specified, the direction and distance along which the bars will spread is calculated automatically from the host structural object, by taking the normal direction of the base sketch, and taking its intersection with the structural object. If you specify a direction vector, the length of that vector will also be taken into account.
- The spacing value is calculated from the current amount of bars, and represents the distance between the axes of each bar. You must therefore subtract the bar diameter to obtain the size of the free space between bars.
- DATAAmount: The amount of bars.
- DATADiameter: The diameter of the bars.
- DATADirection: The direction (and length) along which the bars must spread. If the value is (0,0,0), the direction is calculated automatically from the host structural object.
- DATAOffset Start: The offset distance between the border of the structural object and the first bar.
- DATAOffset End: The offset distance between the border of the structural object and the last bar.
- DATARounding: A rounding value to be applied to the corners of the bars, expressed in times the diameter.
- DATASpacing: The distance between the axes of each bar.
Rebar = makeRebar(baseobj=None, sketch=None, diameter=None, amount=1, offset=None, name="Rebar")
- Creates a
Rebarobject from the given
baseobj, which is an Arch Structure, and a
offsetare used to define the characteristics of the bars.
- If no
offsetvalues are given, the default values from the Arch Preferences are used.
import FreeCAD, Arch, Part Structure = Arch.makeStructure(None, length=1000, width=1000, height=3000) Structure.ViewObject.Transparency = 80 FreeCAD.ActiveDocument.recompute() p1 = FreeCAD.Vector(-400, 400, 0) p2 = FreeCAD.Vector(400, 400, 0) Sketch = FreeCAD.ActiveDocument.addObject('Sketcher::SketchObject', 'Sketch') Sketch.MapMode = "FlatFace" Sketch.Support = [(Structure, "Face6")] Sketch.addGeometry(Part.LineSegment(p1, p2)) FreeCAD.ActiveDocument.recompute() Rebar = Arch.makeRebar(Structure, Sketch, diameter=80, amount=7, offset=50) Rebar.OffsetStart = 100 Rebar.OffsetEnd = 100 FreeCAD.ActiveDocument.recompute()