Scheduled For Release 2019-12-31
0004054: [Bug] lengths in reference mode length are treated redundant
0004055: [Bug] wrong default value for grid size
0004001: [Bug] Sketcher trimming issue with arcs
0003576: [Feature] Orthogonally restrict dragging of geometry in Sketcher (invoked by pressing ctrl or shift or ctrl+shift)
0003374: [Feature] Sketch + Gui.SelectionEx() - - - Identify Geometry Index Outside Edit Mode
0002774: [Feature] Can not select points in sketcher properly when changing viewangle
0003181: [Feature] Allow to toggle the construction of points
0003086: [Feature] CTRL key during line operation increase the snap active area such that it is easy to match points
0003203: [Feature] More convenient arc-drawing in polyline mode
0002492: [Feature] Multiple entities overlayed
0003107: [Feature] Customize Sketcher units
0001343: [Feature] Request for additional (dynamic) detail in error messages
0001416: [Feature] Constraints creation "on the fly"
0004056: [Feature] missing sketcher preferences for unconstrained highlighting
0003803: [Feature] Improvement of "Constraints" list in the Sketch task of the "Combo view"
0000845: [Feature] [Sketcher] Sketcher and Transparent solids (abdullah)
0003489: [Feature] Toggle visibility of all construction geometry
0000847: [Feature] [Sketcher] Dragging + snap to grid
0003842: [Bug] undo of move operation results in new state (abdullah)
0004051: [Bug] Hang FC and Linux edit a sketch with edge farrrrr from Origin
0003952: [Bug] Sketcher grid spacing isn't kept
0003978: [Bug] unchanged reference dimensions lose reference mode
0003961: [Bug] DogLeg fail
0001271: [Feature] Allow User to Toggle Automatic Grid Sizeing in Sketcher On and Off
0003910: [Bug] sketch lost tangent constraint using trim
0004087: [Bug] [Crash FC & Function Bug] - Part:FeatureGeometrySet (wmayer)
0004144: [Bug] Sequence of clicks for creating symmetry differs between "select element first" and "constraints continue mode" (abdullah)
0003708: [Feature] Add an Offset tool to the Sketcher (abdullah)
0004105: [Bug] Automated changing of coincidence+line/line tangency with auto remove redundants can remove the wrong constraints (abdullah)
0004053: [Feature] CarbonCopy should use names of constraints if available. (abdullah)
0003793: [Feature] Naming reference constraints on doubleclick (abdullah)
0003668: [Feature] Implement offset curves in the sketcher (abdullah)
0003682: [Feature] Sketch Analysis new tests (abdullah)
0003681: [Feature] Valid profile validation at sketch exit (abdullah)
0003743: [Feature] Control log output of solver (abdullah)
0003659: [Bug] Tangent constraint shows no effect in 3D view (abdullah)
0003718: [Feature] Block constraint does not work on GeomPoints (abdullah)
0003110: [Feature] Sketcher: add support of relevant constraints to B-splines (abdullah)
0003649: [Bug] Improve handling of block constraint if dimensional constraints are involved (abdullah)
0003655: [Bug] GeomAPI_ExtremaCurveCurve fails to detect intersection (upstream OCCT bug) (abdullah)
0003684: [Feature] Support for trimming arcs of hyperbola and arcs of parabola (abdullah)
0003671: [Feature] Sketcher Analysis interface improvements (abdullah)
0003667: [Bug] wrong normals of tangents of ellipses (abdullah)
0003438: [Feature] Show in Sketcher if the sketch is closed (abdullah)
0003660: [Feature] Infinite lines in Sketcher (abdullah)
0002052: [Feature] Add Chamfer Edge-Tool (abdullah)
0001436: [Feature] Sketcher: Break a Line and Add a Point onto a Line (abdullah)
0002078: [Feature] Support to apply equality constraint on angles (abdullah)
0001560: [Feature] Provide ability to fine-tune auto constraints. (abdullah)
0003926: [Bug] Carbon copy in construction mode reports wrong constraint redundancy. (abdullah)
0003973: [Bug] Carbon copy of a sketch results in unresolvable sketch (abdullah)
0004013: [Bug] Sketcher falsely reports line already constrained (horizontal/vertical) (abdullah)
0004012: [Feature] Sketcher should handle zero length lines better (abdullah)
4 of 53 issue(s) resolved. Progress (7%). View Issues