Part: Instrumentul Loft

From FreeCAD Documentation
Revision as of 10:27, 3 October 2018 by Luc (talk | contribs)

Part Loft

poziția meniului
Part → Loft...
Ateliere
Part
scurtătură
nici unul
Prezentat în versiune
-
A se vedea, de asemenea,
Part Sweep

Prezentare generală

Instrumentul Loft din Atelierul (Part Workbench) este utilizat pentru a crea o fațetă, o cochilie sau o formă solidă (corp) plecând de la două sau mai multe profiluri. Profilele pot fi un punct (vertex), o linie (margine), o polilinie sau o fațetă. Muchiile și poliliniile pot fi deschise sau închise. Există mai multe limitări și complicații limitations and complications , vezi mai jos, însă profilurile pot proveni de la primitivele geometrice din Atelierul Part/Piese, de la funcționalitățile Aelierului Draft Workbench și de la Atelierul Sketch.

Instrumentul Loft are trei parametrii, "Ruled","Solid" and "Closed" fiecare având câte o valoare sau "true" ori "false".

Dacă este true" , "Ruled" FreeCAD creează o fațetă, fațetele sau solidele din suprafețele riglate. Ruled surface page on Wikipedia.

Dacă "Solid" are valoarea "true" FreeCAD creează un solid dacă profilele sunt forme geometrice închise, dacă valorea este "false" FreeCAD creează o fațetă sau (dacă are mi mult de o fațetă) o cochilie dacă este un profil închis sau deschis.

FreeCAD încearcă să atașeze ultimul profil la primul profil pentru a crea o figură închisă.

Pentru mai multe informații supra modului cum profilele sunt legate împreună , referiți-vă la pagina Part Loft Technical Details .

Part_Loft. From three profiles which are two Part_Circles and one Part_Ellipse. Parameters are Solid "True" and Ruled "True"

Limitări și complicații

  • Un vertex sau un punct
    • vârful sau punctul pot fi utilizate numai ca primul și / sau ultimul profil din lista de profiluri.
      • De examplu
        • you cannot loft from a circle to a point, to an ellipse.
        • However you could Loft from a point to a circle to an ellipse to another point.
  • Open or closed geometry profiles can not be mixed in one single Loft
    • In one Loft, all profiles (lines wires etc.) must be either open or closed.
      • De examplu
        • FreeCAD can not Loft between one Part Circle and one default Part Line.
  • Draft Workbench features
    • Draft Workbench features can be directly used as a profile in FreeCAD 0.14 or later.
      • For example the following Draft features can be used as profiles in a Part Loft
        • Draft Polygon.
        • Draft Point, Line, wire,
        • Draft B-spline, Bezier Curve
        • Draft Circle, Ellipse, Rectangle
  • Schițe PartDesign Sketches
    • The profile may be created with a sketch. However only a valid sketch will be shown in the list to be available for selection.
    • The sketch must contain only one open or closed wire or line (can be multiple lines, if those lines are all connected as they are then a single wire)
  • Atelierul Part Workbench
    • the profile can be a valid Part geometric primitive which can be created with the Part CreatePrimitives tool
      • De examplu următoarele primiteve geometrice Part pot fi un profil valid
        • Punct (Vertex), Linie (Edge)
        • Elice, Spirală
        • Cerc, Elipsă
        • Poligon Regulat
        • Plan (Fațetă)
  • Closed Lofts
    • Rezultatele loft-urilor închise pot fi neașteptate - mansarda/loft ul poate dezvolta răsuciri sau deformări. Lofting-ul este foarte sensibil la Plasamentul profilurilor și la complexitatea curbelor necesare pentru conectarea Vârfurilor corespunzătoare în toate profilurile.

Un exemplu de Loft

Instrumentul Loft este în Atelierul Part Workbench, meniul Part -> Loft... sau via iconița din bara de instrumente.

In the "Tasks" will be two lists: "node / wire" and "free form".

Selecția elementelor

In the "node / wire" the available items are displayed. Two elements must be selected one after the first in this list.


Thereafter, with the blue arrow that item is added to the list of "free form".

The selected items must be of the same type.

Tip: the active / selected items in the list are displayed in the 3D area as active / selected.

Comanda completă

Dacă sunt selectate ambele elemente, comanda poate fi completată cu "OK".

Rezultat

Din liniile închise obținem suprafețe care ar putea fi luate ca un aspect superficial pentru solide.

Dacă într-adevăr trebuie să creați un solid, utilizați butonul "Create Solid" sau după ce ați creat comutatorul Loft în tab-ul properties data și setați comutatorul "Solid" la True.

Procedura este aceeași cu cea descrisă mai sus cu polilinii deschise.

Versiunile FreeCAD

  • adăugată în Version 0.13
  • proprietatea "closed" a fost adăugată la Version 0.14
  • Abilitatea de a folosi fațeta ca pe un profil a fost adăugată în Version 0.14