Arch: Armatura di trave

From FreeCAD Documentation
Revision as of 22:00, 15 October 2019 by Renatorivo (talk | contribs) (Created page with "====Esempio====")

Rinforzo trave

Posizione nel menu
Arch → Strumenti armatura
Ambiente
Arch, BIM
Avvio veloce
Nessuno
Introdotto nella versione
0.19
Vedere anche
Rinforzo di colonna due staffe sei barre, Armatura

Descrizione

Lo strumento Rinforzo di trave consente all'utente di creare delle barre di rinforzo all'interno di un oggetto Struttura Trave.

Questo comando fa parte del addon Reinforcement, che si può installare con Addon manager, tramite il menu Strumenti → Addon manager → Reinforcement.

Rinforzo di trave all'interno di una Struttura trave

Utilizzo

1. Seleziona la faccia destra di un oggetto Struttura trave precedentemente creata, avente la lunghezza sull'asse x. Oppure seleziona la faccia anteriore di un oggetto Struttura trave precedentemente creata, avente la lunghezza sull'asse y.

2. Quindi selezionare Rinforzo di trave dagli Strumenti armatura.

3. Appare una finestra di dialogo come quella mostrata sotto.

Finestra di dialogo per lo strumento Rinforzo di trave

4. Selezionare il tipo desiderato di rinforzo di trave.

Fornire gli input per i dati relativi alle staffe.

6. Fare clic su Avanti e la finestra di dialogo viene aggiornata come mostrato di seguito.


Finestra di dialogo per i dati della parte superiore dell'armatura


Impostare i dati per le armature superiori.

- Per editare i valori Number#Diameter@Offset, fare clic sul pulsante accanto all'etichetta Number#Diameter@Offset. Appare una finestra di dialogo come mostrato di seguito.

- Per modificare il valore di Rebar Type, fare clic sul pulsante Modifica accanto all'etichetta Rebar Type. Appare una finestra di dialogo come mostrato di seguito.

- Per modificare il valore di Orientamento gancio, fare clic sul pulsante Modifica accanto all'etichetta Hook Orientation. Appare una finestra di dialogo come mostrato di seguito.

- Per modificare il valore dell'estensione del gancio, fare clic sul pulsante Modifica accanto all'etichetta Hook Extension. Appare una finestra di dialogo come mostrato di seguito.

- Per modificare il valore dell'arrotondamento della barra, fare clic sul pulsante Modifica accanto all'etichetta Rounding. Appare una finestra di dialogo come mostrato di seguito.

- Per modificare il valore di spaziatura dei livelli, fare clic sul pulsante Modifica accanto all'etichetta Layer Spacing. Appare una finestra di dialogo come mostrato di seguito.

6. Fare clic su Avanti e la finestra di dialogo viene aggiornata come mostrato di seguito.

Finestra di dialogo per i dati della parte inferiore dell'armatura

9. Impostare i dati per le armature inferiori in modo simile ai dati delle armature superiori.

6. Fare clic su Avanti e la finestra di dialogo viene aggiornata come mostrato di seguito.

Definire i dati per le barre di rinforzo sul lato sinistro.

11. Impostare i dati per le armature di taglio a sinistra.

- Per editare i valori Number#Diameter@Offset, fare clic sul pulsante accanto all'etichetta Number#Diameter@Offset. Appare una finestra di dialogo come mostrato di seguito.

- Per modificare il valore di Rebar Type, fare clic sul pulsante Modifica accanto all'etichetta Rebar Type. Appare una finestra di dialogo come mostrato di seguito.

- Per modificare il valore di Orientamento gancio, fare clic sul pulsante Modifica accanto all'etichetta Hook Orientation. Appare una finestra di dialogo come mostrato di seguito.

- Per modificare il valore dell'estensione del gancio, fare clic sul pulsante Modifica accanto all'etichetta Hook Extension. Appare una finestra di dialogo come mostrato di seguito.

- Per modificare il valore dell'arrotondamento della barra, fare clic sul pulsante Modifica accanto all'etichetta Rounding. Appare una finestra di dialogo come mostrato di seguito.

6. Fare clic su Avanti e la finestra di dialogo viene aggiornata come mostrato di seguito.

Definire i dati per le barre di rinforzo sul lato destro.

13. Impostare i dati per le armature di taglio a destra in modo simile ai dati delle armature di taglio a sinistra.

14. Cliccare su OK o su Applica per generare l'armatura.

15. Cliccare Cancella per uscire dalla finestra di dialogo.

Proprietà

Stirrups:

  • DatiLeft Cover: a distanza tra l'estremità sinistra della staffa e la faccia sinistra della struttura - copriferro a sinistra.
  • DatiRight Cover: la distanza tra l'estremità destra della staffa e la faccia destra della struttura - copriferro a destra.
  • DatiTop Cover: la distanza tra la staffa e la faccia superiore della struttura.
  • DatiBottom Cover: la distanza tra la staffa e la faccia inferiore della struttura.
  • DatiOffset: la distanza tra la staffa e la faccia superiore e inferiore della struttura.
  • DatiDiameter: diametro della staffa.
  • DatiBent Angle: l'angolo dipiega definisce l'angolo alle estremità di una staffa.
  • DatiExtension Factor: il fattore di estensione definisce la lunghezza dell'estremità della staffa, espressa in volte il diametro.
  • DatiNumber: il numero di staffe.
  • DatiSpacing: la distanza tra gli assi di ogni staffa.


Top/Bottom Reinforcement Rebars: barre di armatura presenti nella parte superiore e inferiore della trave

  • DatiNumberDiameterOffset: Una tupla della stringa Number#Diameter@Offset. Ogni elemento della tupla rappresenta il rinforzo per ogni nuovo livello.
  • DatiRebar Type: Elenco di tuple del tipo di barre di rinforzo.
  • DatiHook Orientation: Elenco di tuple di orientamento dei ganci a forma di L.
  • DatiHook Extension: Elenco di tuple di lunghezza del gancio a forma di L delle armature.
  • DatiRounding: Elenco di tuple del valore di arrotondamento da applicare agli angoli delle armature a forma di L, espresse in volte il diametro.
  • DatiLayer Spacing: Elenco di spaziatura tra due strati di rinforzo consecutivi.


Left/Right Reinforcement Rebars: Rebars present at left/right side of beam

  • DatiNumberDiameterOffset: String of Number#Diameter@Offset set for reinforcement bars.
  • DatiRebar Type: List of type of reinforcement bars.
  • DatiHook Orientation: List of orientation of LShaped hooks.
  • DatiHook Extension: List of length of hook of LShaped rebars.
  • DatiRounding: List of a rounding value to be applied to the corners of the LShape rebars, expressed in times the diameter.
  • DatiRebar Spacing: Clear spacing between consecutive reinforcement bars.

Script

See also: Arch API, Reinforcement API and FreeCAD Scripting Basics.

The BeamReinforcement tool can be used in macros and from the Python console by using the following function:

Create Two Legged Stirrups

RebarGroup = makeReinforcement(
    l_cover_of_stirrup,
    r_cover_of_stirrup,
    t_cover_of_stirrup,
    b_cover_of_stirrup,
    offset_of_stirrup,
    bent_angle,
    extension_factor,
    dia_of_stirrup,
    number_spacing_check,
    number_spacing_value,
    top_reinforcement_number_diameter_offset,
    top_reinforcement_rebar_type,
    top_reinforcement_layer_spacing,
    bottom_reinforcement_number_diameter_offset,
    bottom_reinforcement_rebar_type,
    bottom_reinforcement_layer_spacing,
    left_rebars_number_diameter_offset,
    left_rebars_type,
    left_rebars_spacing,
    right_rebars_number_diameter_offset,
    right_rebars_type,
    right_rebars_spacing,
    top_reinforcement_l_rebar_rounding=2,
    top_reinforcement_hook_extension=40,
    top_reinforcement_hook_orientation="Front Inside",
    bottom_reinforcement_l_rebar_rounding=2,
    bottom_reinforcement_hook_extension=40,
    bottom_reinforcement_hook_orientation="Front Inside",
    left_l_rebar_rounding=2,
    left_rebars_hook_extension=40,
    left_rebars_hook_orientation="Front Inside",
    right_l_rebar_rounding=2,
    right_rebars_hook_extension=40,
    right_rebars_hook_orientation="Front Inside",
    structure=None,
    facename=None,
)
  • Creates a RebarGroup object from the given structure, which is an Arch Structure, and facename, which is a face of that structure.
    • If no structure nor facename are given, it will take the user selected face as input.
  • l_cover_of_stirrup, r_cover_of_stirrup, t_cover_of_stirrup, b_cover_of_stirrup and offset_of_stirrup are inner offset distances for the stirrup elements with respect to the faces of the structure. They are respectively the left, right, top, bottom and front/rear offsets.
  • bent_angle define the angle of the tip of the reinforcement loop of stirrup.
  • extension_factor define the length of the tip of the reinforcement loop of stirrup, expressed in times the diameter.
  • dia_of_stirrup is the diameter of the stirrup.
  • number_spacing_check if it is True it will create as many stirrup as given by number_spacing_value; if it is False it will create stirrup separated by the numerical value of number_spacing_value.
  • number_spacing_value specifies the number of stirrups, or the value of the separation between them, depending on number_spacing_check.
  • top_reinforcement_number_diameter_offset and bottom_reinforcement_number_diameter_offset are tuple of number_diameter_offset string. Each element of tuple represents reinforcement for each new layer.
   Syntax: (
               "number1#diameter1@offset1+number2#diameter2@offset2+...",
               "number3#diameter3@offset3+number4#diameter4@offset4+...",
               ...,
           )
  • top_reinforcement_rebar_type and bottom_reinforcement_rebar_type specifies type of top/bottom reinforcement bars.
   Possible values:
   1. 'StraightRebar' or 'LShapeRebar'
   2. ('<rebar_type>', '<rebar_type>', ...) and number of elements of tuple must be equal to number of reinforcement
      layers.
   3. [
          ('<rebar_type>', '<rebar_type>', ...),
          ('<rebar_type>', '<rebar_type>', ...),
          ...,
      ]
      each element of list is a tuple, which specifies rebar type of each reinforcement layer. And each element of
      tuple represents rabar_type for each set of rebars.
   4. [
          <rebar_type>,
          ('<rebar_type>', '<rebar_type>', ...),
          ...,
      ]
  • top_reinforcement_layer_spacing and bottom_reinforcement_layer_spacing is the spacing between two consecutive reinforcement layers.
   Possible values:
   1. <layer_spacing>
   2. (<spacing in layer1 and layer2>, <spacing in layer2 and layer3>, ...) and number of elements of tuple must be
      equal to one less than number of layers.
  • left_rebars_number_diameter_offset and right_rebars_number_diameter_offset are string of number_diameter_offset.
   Syntax: "number1#diameter1@offset1+number2#diameter2@offset2+..."
  • left_rebars_type and right_rebars_type specifies type of left/right reinforcement bars.
   Possible values:
   1. 'StraightRebar' or 'LShapeRebar'
   2. ('<rebar_type>', '<rebar_type>', ...) and each element of tuple represents rabar_type for each set of rebars.
  • left_rebars_spacing and right_rebars_spacing is clear spacing between consecutive reinforcement bars.
  • top_reinforcement_l_rebar_rounding and bottom_reinforcement_l_rebar_rounding is the parameter that determines the bending radius of the LShaped top/bottom rebars, expressed as times the diameter. Possible syntax are similar to as discussed above for top_reinforcement_rebar_type / bottom_reinforcement_rebar_type.
  • top_reinforcement_hook_extension and bottom_reinforcement_hook_extension is the length of hook of LShaped rebars. Possible syntax are similar to as discussed above for top_reinforcement_rebar_type / bottom_reinforcement_rebar_type.
  • top_reinforcement_hook_orientation and bottom_reinforcement_hook_orientation specifies the orientation of LShaped hook; it can be "Front Inside", "Front Outside", "Rear Inside" or "Rear Outside". Possible syntax are similar to as discussed above for top_reinforcement_rebar_type / bottom_reinforcement_rebar_type.
  • left_l_rebar_rounding and right_l_rebar_rounding is the parameter that determines the bending radius of the LShaped left/right rebars, expressed as times the diameter. Possible syntax are similar to as discussed above for left_rebars_type / right_rebars_type.
  • left_rebars_hook_extension and right_rebars_hook_extension is the length of hook of LShaped rebars. Possible syntax are similar to as discussed above for left_rebars_type / right_rebars_type.
  • left_rebars_hook_orientation and right_rebars_hook_orientation specifies the orientation of LShaped hook; it can be "Front Inside", "Front Outside", "Rear Inside" or "Rear Outside". Possible syntax are similar to as discussed above for left_rebars_type / right_rebars_type.

Esempio

import FreeCAD, Arch
from BeamReinforcement import TwoLeggedBeam

Structure = Arch.makeStructure(length=3000.0,width=200.0,height=400.0)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()

RebarGroup = TwoLeggedBeam.makeReinforcement(
    l_cover_of_stirrup=20,
    r_cover_of_stirrup=20,
    t_cover_of_stirrup=20,
    b_cover_of_stirrup=20,
    offset_of_stirrup=100,
    bent_angle=135,
    extension_factor=4,
    dia_of_stirrup=8,
    number_spacing_check=False,
    number_spacing_value=200,
    top_reinforcement_number_diameter_offset=("1#20@-60+2#16@-60+1#20@-60", "3#16@-100"),
    top_reinforcement_rebar_type="LShapeRebar",
    top_reinforcement_layer_spacing=30,
    bottom_reinforcement_number_diameter_offset=("1#20@-60+2#16@-60+1#20@-60", "3#16@-100"),
    bottom_reinforcement_rebar_type="LShapeRebar",
    bottom_reinforcement_layer_spacing=30,
    left_rebars_number_diameter_offset="1#16@-100+1#16@-100+1#16@-100",
    left_rebars_type="LShapeRebar",
    left_rebars_spacing=30,
    right_rebars_number_diameter_offset="1#16@-100+1#16@-100+1#16@-100",
    right_rebars_type="LShapeRebar",
    right_rebars_spacing=30,
    top_reinforcement_l_rebar_rounding=2,
    top_reinforcement_hook_extension=100,
    top_reinforcement_hook_orientation="Rear Outside",
    bottom_reinforcement_l_rebar_rounding=2,
    bottom_reinforcement_hook_extension=100,
    bottom_reinforcement_hook_orientation="Rear Outside",
    left_l_rebar_rounding=2,
    left_rebars_hook_extension=80,
    left_rebars_hook_orientation=("Rear Inside", "Front Inside", "Rear Inside"),
    right_l_rebar_rounding=2,
    right_rebars_hook_extension=80,
    right_rebars_hook_orientation=("Front Inside", "Rear Inside", "Front Inside"),
    structure=Structure,
    facename="Face6",
)